Zenoah G5300 manual Tensioning the chain

Page 12

GENERAL SAFETY PRECAUTIONS

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

 

!

WARNING! A slack chain may jump off

 

and cause serious or even fatal injury.

 

 

 

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner.Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

12 – English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s manual KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents What is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainFitting a spike bumper Protect your hands from injuryFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a tree that has fallen badly Freeing a trapped treeHow to avoid kickback What is kickback?General advice Cutting trees and branches that are in tensionCutting the trunk into logs Maintenance Carburettor adjustmentGeneral Correctly adjusted carburettor High speed jet HChecking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugLubricating the bar tip sprocket Needle bearing lubricationAdjustment of the oil pump Dust Free centrifugal cleaningTemperature 0C or colder Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges EC-declaration of conformityApplies to Europe only EN ISO 12100-22003, Cispr 122005, EN ISOLimited Warranty Limited warranty1151331-26

G5300 specifications

The Zenoah G5300 is a highly regarded two-stroke gasoline engine, well-known for its robust performance and reliability within the realm of outdoor power equipment. Its engineering reflects a commitment to innovation and efficiency, making it ideal for various applications such as brush cutters, chainsaws, and other handheld equipment.

One of the key features of the G5300 is its displacement, which typically measures around 53cc. This size strikes an excellent balance between power output and weight, enabling users to tackle demanding tasks without the burden of a heavy machine. The engine's design leverages a high power-to-weight ratio, resulting in enhanced maneuverability and ease of use, particularly in tight spaces.

The G5300 utilizes a sophisticated electronic ignition system. This technology ensures reliable starting, consistent performance, and reduced emissions. The engine also features a dual-ring piston, which improves compression efficiency and enhances overall power delivery. This design contributes to a smoother operation and helps extend the life of the engine.

Another notable characteristic of the Zenoah G5300 is its fuel efficiency. With advancements in combustion technology, the engine is designed to reduce fuel consumption while still providing ample power. This not only lowers operational costs for the user but also minimizes environmental impact, aligning with contemporary preferences for sustainable practices in outdoor equipment.

Durability is another hallmark of the G5300. Built with high-quality materials, the engine is designed to withstand the rigors of outdoor use. The components are rigorously tested to ensure they can handle extreme conditions, whether it's scorching heat or chilly weather. The engine's construction also includes vibration dampening features, enhancing user comfort during extended operations.

Serviceability is a consideration in the design of the G5300, with easily accessible components promoting straightforward maintenance. Users can quickly perform routine checks, tune-ups, and repairs, minimizing downtime and extending the lifespan of the equipment.

In summary, the Zenoah G5300 stands out in the outdoor power equipment market due to its powerful and efficient design. With a focus on durability, serviceability, and fuel efficiency, it meets the demands of both professional landscapers and hobbyist gardeners alike. Its blend of advanced technology and practical features makes it a reliable choice for anyone seeking a high-performance engine for their outdoor tasks.
Top Page Image Contents