Telex Plasma Series manual Description, System Features Plasma, System Setup

Page 5

Description

Electro-Voice®Plasma high powered loudspeakers are fully integrated audio systems with carefully matched electronics and transducers. These products make it easy to setup a high- quality sound system quickly with a minimum of cables and external electronics. It retains typical EV ruggedness, reliability and impeccable sound quality.

System Features - Plasma

·Two built-in power amplifiers, one for low frequencies and one for high frequencies. The amplifiers also contain electronic crossover circuitry and CD horn compensation optimized for the speaker components a well as a limiter circuit that prevents either amplifier from clipping while preserving the sonic quality.

·The low-frequency power amplifier delivers 500 watts continuous average power.

·The high-frequency power amplifier delivers 150 watts continuous average power.

·The subwoofer power amplifier delivers 800 watts continuous average power.

·The line input utilizes Neutrik “combo” connectors, which will accept either ¼-inch or 3-pin XLR- type connectors.

·The separate line output is a 3-pin XLR-type that can be used to connect additional systems.

·The Plasma P1 two-way system is perfect for use as powered floor monitors.

·Neutrik Powercon connectors are used for AC power connections. They provide a positive locking feature to prevent accidental disconnection.

System Setup

To get your Plasma system into operation as quickly as possible, please observe the following steps and precautions.

·Plug the 3-terminal Powercon ac cable into a grounded line receptacle. Extension cords can be used to lengthen the ac cable as necessary but make sure that they are 3-conductor 14 gauge or greater, and that are properly grounded to avoid electrical hazards and extraneous noise.

·Be sure that the Plasma system is plugged into an ac power source that is capable of supplying the correct voltage. If the line voltage drops too much, the built-in amplifiers won’t be able to develop their rated power and sound quality will suffer. Under high signal conditions, the Plasma amplifier section can pull 3 – 4 amps of current (120 volt models) (2 amps at 240 volts). That means that no more than 4-Plasma systems should be plugged into a single 15 amp electrical service. Be cautious of what else is plugged into the same electrical service line to avoid electrical problems and poor performance.

·BEFORE TURNING THE POWER ON, MAKE SURE THAT THE LEVEL CONTROLS ARE DOWN TO AVOID TRANSIENTS OR UNEXPECTED LOUD SOUND. Turn on the power switch and ensure that the system is receiving power by monitoring the status LED. If the system is receiving signal, the LED will illuminate green.

ELECTRO-VOICE®￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Plasma Series Important Service Instructions Important Safety InstructionsTable of Contents Make sure to Safety FirstDescription System Features PlasmaSystem Setup P1 and P2 Amplifiers Input SignalStatus Indicators Setup Diagrams for Plasma Plasma P1 Rigging Using Plasma P1’s as Floor MonitorsSuspending Plasma P1 Speaker Systems Dimensions Plasma P1 SpecificationsDimensions Plasma P2 Subwoofer Block Diagrams ELECTRO-VOICE ELECTRO-VOICE ELECTRO-VOICE

Plasma Series specifications

The Telex Plasma Series represents a significant leap forward in the realm of high-definition audio technology, combining innovative design with cutting-edge features that cater to both audiophiles and casual listeners. One of the standout characteristics of the Plasma Series is its commitment to delivering exceptional sound clarity and precision across the entire audio spectrum. This range of products leverages advanced technologies to ensure that users experience music and sound as the artist intended.

At the heart of the Telex Plasma Series is its proprietary plasma technology, which utilizes ionization to create ultra-fast sound waves. This results in an extremely responsive audio output that captures even the most delicate nuances of a musical performance. This technology allows for a dynamic range that can reproduce low frequencies with powerful depth while maintaining crystal-clear high frequencies.

Another notable feature of the Plasma Series is its sleek and modern aesthetic, designed to complement any home or professional environment. The materials used in construction provide not only durability but also enhance the overall acoustic performance. Each unit is meticulously engineered to minimize resonance and distortion, ensuring that every note played is crisp and clear.

Connectivity is a primary consideration in the design of the Telex Plasma Series. The products support various input options, including Bluetooth, HDMI, and traditional RCA connections, allowing users to seamlessly integrate the systems into their existing setups. Additionally, the built-in equalizer settings enable personalized sound tuning, tailored to individual listening preferences and room acoustics.

Furthermore, the Telex Plasma Series is designed with energy efficiency in mind, delivering powerful performance without excessive power consumption. Many models incorporate smart technology that detects when the system is not in use, automatically entering a low-power standby mode.

In summary, the Telex Plasma Series combines groundbreaking plasma technology, elegant design, versatile connectivity, and energy efficiency to provide an unparalleled audio experience. Whether for enjoying music at home or in a professional setting, the Plasma Series stands out as a top choice for anyone seeking high-quality sound and innovation in their audio equipment.
Top Page Image Contents