Zenoah G500AVS owner manual Fuel and Chain Oil

Page 8

G455AVS / G500AVS

4. Fuel and Chain Oil

FUEL

WARNING

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refuel- ing the unit. Select outdoor bare ground for fuel- ing and move at least 3 m (10 ft) away from the fueling point before starting the engine.

The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use (JASO FC GRADE OIL or ISO EGC GRADE).

Do not use BIA or TCW (2-stroke water-cooling type) mixed oil.

RECOMMENDED MIXING RATIO GASOLINE 50 : OIL 1

(when using ZENOAH genuine oil)

Exhaust emission are controlled by the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of any major hardware or the intro- duction of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89RON (USA/Canada: 87AL).

If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine tem- perature may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

WARNING

Pay attention to agitation.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to

GB-8

agitate depending on oil ingredients, sufficient agi- tation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to ab- normally lean mixture.

5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6.Indicate the contents on outside of container for easy identification.

FUELING THE UNIT

1.Untwist and remove the fuel cap. Rest the cap on a dustless place.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select flat and bare ground for fueling.

2.Move at least 10 feet (3 meters) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID:

1.FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2.GASOHOL – It can cause deterioration of rubber and/ or plastic parts and disruption of engine lubrication.

3.OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4.Mixed fuels which have been left unused for a period of one month or more may clog the carbu- retor and result in the engine failing to operate prop- erly.

5.In the case of storing the product for a long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6.In the case of scrapping the used mixed oil con- tainer, scrap it only at an authorized repository site.

NOTE

As for details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, nor- mal wear and change in product with no functional in- fluence are not covered by the warranty. Also, be care- ful that, if the usage in the instruction manual is not ob- served as to the mixed gasoline, etc. described therein, it may not be covered by the warranty.

CHAIN OIL

Use motor oil SAE #10W-30 all year round or SAE #30 ~ #40 in summer and SAE #20 in winter.

NOTE

Do not use wasted or regenerated oil that can cause damage to the oil pump.

Image 8
Contents G455AVS / G500AVS GB-1Wear head, eye and ear protection LpA LwA45.0 cm3 102.5 dBA 110 dBA 49.3 cm3 103.6 dBA 110 dBAContents Always shut off the engine be- fore setting it down For safe operationGB-5 Kickback Safety Precau Tions for Chain SAW UsersKickback may occur when the nose or tip of the guide bar Explanation of Symbols on the Machine Port to refuel MIX GasolinePosition Fuel cap Port to top up chain oilPay attention to the correct direction of the saw chain Installing Guide Bar and Saw ChainStandard saw unit package contains the items as illustrated Fuel and Chain Oil Adjusting the Carburetor Operating the EngineStarting the Engine Checking the OIL SupplyHow to confirm HOW to Switch Between Operating ModesChain Brake Stopping the EngineSawing Before proceeding to your jobGuard Against Kickback Felling a TreePeriodical Service Points MaintenanceMaintenance After Each USE Maintenance of Saw Chain and Guide Bar Troubleshooting Guide Case 2. Lack of power/Poor acceleration/ Rough idlingDisposal Reverse the bar occasionally to prevent partial wearSpecifications Limited warrantyPower unit Cutting head

G500AVS specifications

The Zenoah G500AVS is a standout product in the world of high-performance engines, specifically designed for a wide range of applications, including remote-controlled vehicles, industrial tools, and gardening equipment. This engine combines power, efficiency, and advanced technology to meet the demands of both hobbyists and professionals.

One of the primary features of the G500AVS is its powerful 50cc displacement, which enables it to deliver an impressive output of torque and horsepower. This capability makes it suitable for applications requiring substantial lifting and cutting strength, such as lawn mowers and chainsaws. The engine is equipped with a lightweight construction, allowing for easier handling without compromising on performance.

The G500AVS utilizes a unique anti-vibration system (AVS) that significantly reduces vibrations during operation. This system not only enhances user comfort but also contributes to the longevity of the engine by minimizing wear and tear on crucial components. The incorporation of AVS technology is a key selling point, particularly for users who spend extended periods operating equipment powered by this engine.

In terms of fuel efficiency, Zenoah has engineered the G500AVS with a fuel-efficient design that minimizes consumption while maximizing output. This is essential for users looking to reduce operational costs without sacrificing performance. Additionally, the engine features an easy-start system, making it user-friendly and accessible for operators of all skill levels.

The G500AVS also incorporates advanced ignition technology, which provides reliable starting and consistent performance in various environmental conditions. This feature is essential for ensuring that the engine performs optimally, regardless of temperature or humidity levels.

Another notable characteristic of the Zenoah G500AVS is its robust build quality. The engine is designed to withstand the rigors of demanding applications, offering durability that is crucial for professionals who rely on their equipment to complete jobs effectively and efficiently.

In summary, the Zenoah G500AVS engine is a top-tier option for anyone in need of a reliable, powerful, and efficient engine. Its combination of advanced features, including an anti-vibration system, fuel efficiency, easy starting, and durable construction, make it an appealing choice for both hobbyists and professionals alike. Whether for recreational use or serious industrial applications, the G500AVS stands out as a model of engineering excellence in the engine market.