Crown Audio CH Series, CL Series operation manual Model CL4 Stereo Mode, Model CL4 Bridge Mode

Page 12

CH and CL Series Power Amplifiers

2 Setup

2.7.7. Model CL4 Stereo Mode

See Figure 2.16. In this example, Channel 1 and

Channel 2 are wired to 4/8-ohm speaker loads.

Make sure the Mode switch is set to the “Stereo” position.

INPUTS: Connect input wiring for each channel.

OUTPUTS:

• Connect Channel 1 positive (+) speaker lead to Channel 1 positive (+) terminal of amp.

• Connect Channel 1 negative (–) speaker lead to Channel 1 negative (–) output terminal of amp.

• Repeat similarly for Channel 2.

Refer to Section 2.5 for output connector pin assignments.

Figure 2.16 Model CL-4 Wiring for Stereo Mode

(Shown with No-Touch Cover Removed)

2.7.8 Model CL4 Bridge Mode

See Figure 2.17. In this example, a 4/8-ohm load is connected in Bridge Mono across the positive terminals of Channel 1 and Channel 2. Make sure the Mode switch is set to the “Bridge” posi- tion.

NOTE: When operating in Bridge-Mono mode, turn down (full CCW) the level control for Channel 2, as the Channel-1 level control works both channels.

INPUTS: Connect input wiring to CH1.

OUTPUTS: Connect positive (+) speaker lead to Channel 1 positive (+) terminal of amp. Connect negative (–) speaker lead to Channel 2 positive

(+) terminal of amp. Do not connect to negative output terminals.

Refer to Section 2.5 for output connector pin assignments.

Figure 2.17 Model CL4 Wiring for Bridge Mode

page 12

(Shown with No-Touch Cover Removed)

Operation Manual

Image 12

Contents CH and CL Series Some models may be exported under the name AmcronImportant Safety Instructions Use only with a cart, stand, tripod, bracket, orSafety Standard Crown International, IncEuropean Representatives Name and Address EMC StandardsTable of Contents Features How to Use This ManualWelcome Setup Unpack Your Amplifier Install Your AmplifierChoose Input Wire and Connectors Choose Output Wire and ConnectorsReinstall no-touch cover to maintain safety Switch Settings Model CH4 Models CH1 and CH2Wire Your System Models CH1 & CH2 Stereo Mode Refer to .5 for output connector pin assign- mentsModels CH1 & CH2 140V Bridge Mode Model CH4 Stereo Mode Model CH4 Bridge ModeInputs Connect input wiring to Channel Models CL1 & CL2 Bridge Mode Models CL1 & CL2 StereoModel CL4 Stereo Mode Model CL4 Bridge ModeInputs Connect input wiring to CH1 All Models How to Parallel the Inputs in Stereo Mode Startup ProcedureScrew terminal Connect to AC MainsPrecautions OperationCH and CL Series Front Panel Controls and Indicators Operation Speed Fan-On-Demand Indicators If the amplifier output stage stops operatingControls Advanced Features Options SST-4622 SST-3632SST-4632 Fault Monitoring Location of Fault JackPrecision Detented Level Controls Attenuation in dBPrinciples of Operation CH1, CH2, CL1 and CL2Power Indicator LED is driven from the low-voltage supply Models CL1 & CL2 Circuit Block DiagramCH4 and CL4 Audio Signal Path Model CH4 Circuit Block DiagramModel CL4 Circuit Block Diagram Power Supply Operation Troubleshooting Amplifier output wires have developed a short circuitFlashing Specifications 120V/60 Hz Units, Bridge mono modeKHz at rated THD Ohms 560W Ohms 450WOhms 275W 600WModel CL1 & CL2 CH and CL Series Power Amplifiers Models CH4 & CL4 Damping Factor Typical Output Impedance AC Power Draw Thermal Dissipation Following equation is used to calculate thermal dissipationAC Power Draw Thermal Dissipation AC Power Draw Thermal Dissipation CL2 Service Warranty 12/01Worldwide Except USA & Canada Fax Mo/day/yrThis page Intentionally Left Blank Model Individual or Business Name Phone # Fax #‰ Personal/Consumer ‰ Business/Corporate