Poulan 423813 manual Tilling Hints, Cultivating, Tine Shear Pins

Page 11

OPERATION

TILLING HINTS

CAUTION: Until you are accustomed to handling your tiller, start actual field use with throttle in slow position (mid-way between “FAST” and “IDLE”).

•Tilling is digging into, turning over, and breaking up packed soil before planting. Loose, unpacked soil helps root growth. Best tilling depth is 4" to 6" (10-15 cm). A tiller will also clear the soil of unwanted vegetation. The decomposition of this vegetable matter enriches the soil. Depending on the climate (rainfall and wind), it may be advisable to till the soil at the end of the growing season to further condition the soil.

•You will find tilling much easier if you leave a row un- tilled between passes. Then go back between tilled rows. (See Fig. 14) There are two reasons for doing this. First, wide turns are much easier to negotiate than about-faces. Second, the tiller won’t be pulling itself, and you, toward the row next to it.

•Soil conditions are important for proper tilling. Tines will not readily penetrate dry, hard soil which may contribute to excessive bounce and difficult handling of your tiller. Hard soil should be moistened before tilling; however, extremely wet soil will “ball-up” or clump during tilling. Wait until the soil is less wet in order to achieve the best results. When tilling in the fall, remove vines and long grass to prevent them from wrapping around the tine shaft and slowing your tilling operation.

•Do not lean on handle. This takes weight off the wheels and reduces traction. To get through a really tough section of sod or hard ground, apply upward pressure on handle or lower the depth stake.

4

3

2

1

5

6

 

7

FIG. 14

CULTIVATING

Cultivating is destroying the weeds between rows to pre- vent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil. Best digging depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields to protect small plants from being buried.

•Cultivate up and down the rows at a speed which will allow tines to uproot weeds and leave the ground in rough condition, promoting no further growth of weeds and grass (See Fig. 15).

FIG. 15

TINE SHEAR PINS

The tine assemblies on your tiller are secured to the tine shaft with shear pins (See “TINE REPLACEMENT” in the Service and Adjustments section of this manual).

If the tiller is unusually overloaded or jammed, the shear pins are designed to break before internal damage occurs to the transmission.

•If shear pin(s) break, replace only with those shown in the Repair Parts section of this manual.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents PRRT850 Preparation Safety RulesMaintenance and Storage TrainingTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Contents of Hardware PackUnpacking Carton See Fig Install Handle See Figs , 4,Check Tire Pressure Attach Clutch Cable See FigConnect Shift ROD See Fig Remove Tiller from CrateKnow Your Tiller Meets Ansi Safety RequirementsOperation Reverse Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Forward Wheels ONLY/TINES StoppedBefore Starting Engine TurningOuter Side Shields See Fig To TransportTo Start Engine ADD GasolineCultivating Tine Shear PinsTilling Hints Before Each USE MaintenanceLubrication Chart General RecommendationsTo Change Engine OIL See Figs AIR Cleaner See FigEngine Spark Plug CleaningCooling System See Fig MufflerTire Care Service and AdjustmentsTiller To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTine Replacement See Figs , 25, Engine OIL StorageOther Fuel SystemTroubleshooting Points Service Notes L5T 1K6 Customer Service DeptStevens Creek Road Ordan Drive Augusta, GA 30907 USA Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Articles des fabricant du Dept Service Customer Canada AuInitiale d’achat date la de compter à jours ’ENTRETIEN Remarques Labourage Dépannage DE GuideDalimentation Système EntreposageCylindres Moteur DE Huile25 .Fig 24 .Fig Réglages ET Révision26 et 25 26 .Fig23 .Fig Fig la Voir Terre À 23 et 22 .Fig les Voir Terre À Nement’ENTRAÎNEMENT Courroie LA Régler ’ENTRAÎCOURROIELAREMPLACERPOURGuidon DU Hauteur LA Régler Pour Fig la Voir RoieFig la Voir Roue LA Enlever Pour Fig la VoirSilencieux Entretien’ALLUMAGE Bougie NettoyageLubrification MoteurLUBRIFICATION DE Tableau Lubrification DE TableauLubrification Utilisation Chaque AvantDents DES Cisaillement DE Boulons UtilisationBinage Labourage DE Conseils13 .FIG Fig la Voir Moteur DU Démarrage’ESSENCE Réservoir LE Remplir Fig la Voir Labourage Transporter PourExtérieurs Latéraux Déflecteurs Moteur DU Démarrage LE AvantCOM LA Avec -FRAISES DES Utilisation Fig la Voir Profondeur DE JaugeMENT/LESLESEU ROUES-AVANT Marche Roue DE DemanMotobineuse Votre Connaissez Ansi Sécurité DE Exigences AUX ConformeCarton DU Motobineuse LA Enlever MontagePoignee DE Hauteur Pneu DE Pression LA VerifierCoupez poignée, la de l’ensemble teniez vous que Pendant Poignee LA InstallerEt 4, 3, .Fig les Voir Fig la Voir Carton LE DeballerDe Clé 1 Pince 1 pneu à Manomètre 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESDallumage Bougie SommaireClient DU Responsabilités Elle .motobineuse d’une achat votre pour FélicitationsEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité toutePRRT850
Top Page Image Contents