Poulan 423813 manual Service and Adjustments, Tiller, Tire Care

Page 15

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•First loosen handle lock lever.

•Handle can be positioned at different settings between “HIGH” and “LOW” positions.

•Retighten handle lock lever securely after adjusting.

HANDLE

(HIGH POSITION)

HANDLE LOCK

LEVER

HANDLE

(LOW POSITION)

FIG. 20

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the custom- ers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

TIRE CARE

CAUTION: When mounting tires, un- less beads are seated, overinflation can cause an explosion.

•Maintain 20 PSI (1.4 kg/cm2) of tire pressure. If tire pressures are not equal, tiller will pull to one side.

•Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL (See Fig. 21)

•Place blocks under transmission to keep tiller from tipping.

•Remove outer side shield by removing nuts “A” and “B”.

•Remove inner side shield by removing nuts “C” and “D”.

•Remove hairpin clip and clevis pin from wheel.

•Remove wheel and tire.

•Repair tire and reassemble.

CLEVIS

PIN

NUT “C”

NUT “D”

HAIRPIN

CLIP

NUT “B”

 

NUT “A”

INNER SIDE

OUTER SIDE

SHIELD

SHIELD

 

FIG. 21

TO REMOVE BELT GUARD (See Fig. 22)

NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch.

•Remove two (2) screws from side of belt guard.

•Remove hex nut and washer from bottom of belt guard (located behind wheel).

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure.

BELT GUARD

SCREW

AND WASHER

 

 

HEX NUT

 

AND

 

WASHER

 

(LOCATED

 

BEHIND

 

TIRE)

SCREW

HAIRPIN CLIP AND

AND

WASHER

CLEVIS PIN

FIG. 22

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PRRT850 Preparation Safety RulesMaintenance and Storage TrainingTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Contents of Hardware PackUnpacking Carton See Fig Install Handle See Figs , 4,Check Tire Pressure Attach Clutch Cable See FigConnect Shift ROD See Fig Remove Tiller from CrateMeets Ansi Safety Requirements OperationKnow Your Tiller Reverse Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive Forward Wheels ONLY/TINES StoppedBefore Starting Engine TurningOuter Side Shields See Fig To TransportTo Start Engine ADD GasolineTine Shear Pins Tilling HintsCultivating Before Each USE MaintenanceLubrication Chart General RecommendationsAIR Cleaner See Fig EngineTo Change Engine OIL See Figs Spark Plug CleaningCooling System See Fig MufflerService and Adjustments TillerTire Care To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTine Replacement See Figs , 25, Engine OIL StorageOther Fuel SystemTroubleshooting Points Service Notes Customer Service Dept Stevens Creek Road Ordan Drive Augusta, GA 30907 USAL5T 1K6 Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dept Service Customer Canada Au Initiale d’achat date la de compter à joursArticles des fabricant du ’ENTRETIEN Remarques Labourage Dépannage DE GuideDalimentation Système EntreposageCylindres Moteur DE Huile25 .Fig 24 .Fig Réglages ET Révision26 et 25 26 .Fig23 .Fig Fig la Voir Terre À 23 et 22 .Fig les Voir Terre À Nement’ENTRAÎNEMENT Courroie LA Régler ’ENTRAÎCOURROIELAREMPLACERPOURGuidon DU Hauteur LA Régler Pour Fig la Voir RoieFig la Voir Roue LA Enlever Pour Fig la VoirSilencieux Entretien’ALLUMAGE Bougie NettoyageLubrification MoteurLUBRIFICATION DE Tableau Lubrification DE TableauLubrification Utilisation Chaque AvantDents DES Cisaillement DE Boulons UtilisationBinage Labourage DE ConseilsFig la Voir Moteur DU Démarrage ’ESSENCE Réservoir LE Remplir13 .FIG Fig la Voir Labourage Transporter PourExtérieurs Latéraux Déflecteurs Moteur DU Démarrage LE AvantCOM LA Avec -FRAISES DES Utilisation Fig la Voir Profondeur DE JaugeMENT/LESLESEU ROUES-AVANT Marche Roue DE DemanMotobineuse Votre Connaissez Ansi Sécurité DE Exigences AUX ConformeCarton DU Motobineuse LA Enlever MontagePoignee DE Hauteur Pneu DE Pression LA VerifierCoupez poignée, la de l’ensemble teniez vous que Pendant Poignee LA InstallerEt 4, 3, .Fig les Voir Fig la Voir Carton LE DeballerDe Clé 1 Pince 1 pneu à Manomètre 1 usage tout à Couteau Pièces DES SAC DU ContenuFig la Voir D’OPERATEUR Position Montage LE Pour Exiges Outils LESDallumage Bougie SommaireClient DU Responsabilités Elle .motobineuse d’une achat votre pour FélicitationsEn lUtilisation pour Conseils Sécurité DE RèglesEntreposage ET Entretien Motobineuses des Sécurité toutePRRT850
Top Page Image Contents