Poulan 96092001000, 410237 manual Turning, Cultivating, To Transport, Before Starting Engine

Page 9

OPERATION

DEPTH STAKE PIN “RELEASED” POSITION

“LOCKED”

POSITION

NUT “B”

 

OUTER

NUT “A”

SIDE SHIELD

 

FIG. 12

TURNING

•Release the drive control bar.

•Move throttle control to “SLOW” position.

•Place shift lever indicator in “F” (forward) position. Tines will not turn.

•Lift handle to raise tines out of ground.

•Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from tines.

•When you have completed your turn-around, release the drive control bar and lower handle. Place shift le- ver in (till) position and move throttle control to desired speed. To begin tilling, hold drive control bar against the handle.

CULTIVATING

•Use the forward rotating tine drive when cultivating, tilling soft ground or tilling pre-tilled soil.

•Release depth and drag stake pins. Lower drag stake. Pull the depth stake up for increased tilling depth. Place proper pin in hole of depth stake or drag stake to lock in position.

•Place shift lever indicator in forward rotating () till position .

•Hold the drive control bar against the handle to start tilling movement. Tines and wheels will both turn.

•Move throttle control "FAST" position for deep tilling. To cultivate, throttle control can be set at any desired speed, depending on how fast or slow you wish to cultivate.

•Always lower the drag stake when using the forward rotating tine drive.

OUTER SIDE SHIELDS (See Fig. 12)

The back edges of the outer side shields are slotted so that the shields can be raised for deep tilling and lowered for shallow tilling to protect small plants from being buried. Loosen nut “A” in slot and nut “B”. Move shield to desired position (both sides). Retighten nuts.

TO TRANSPORT

CAUTION: Beforeliftingortransporting, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank.

AROUND THE YARD

•Release the depth stake pin. Move the depth stake down to the top hole for transporting the tiller. Place depth stake pin in hole of depth stake to lock in posi- tion. This prevents tines from scuffing the ground.

•Place shift lever indicator in “F” (forward) position for transporting.

•Hold the drive control bar against the handle to start tiller movement. Tines will not turn.

•Move throttle control to desired speed.

AROUND TOWN

•Disconnect spark plug wire.

•Drain fuel tank.

•Transport in upright position to prevent oil leakage.

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN APPROVED, CLEAN, COVERED CONTAINERS. USE CLEAN FILL FUNNELS.

CHECK ENGINE OIL LEVEL (See Fig. 13)

•The engine in your unit has been shipped, from the factory, already filled with SAE 30 summer weight oil.

•With engine level, clean area around oil filler plug and remove plug.

•Engine oil should be to point of overflowing when engine is level. For approximate capacity see “PRODUCT SPECIFICATIONS” on page 3 of this manual. All oil must meet A.P.I. Service Classification SG-SL.

•Reinstall engine oil cap and tighten.

•For cold weather operation you should change oil for easier starting (See oil viscosity chart in the Mainte- nance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

OIL

LEVEL

FIG. 13

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents DRT875 Maintenance and Storage Safety RulesTraining PreparationTable of Contents Tools Required for Assembly AssemblyContents of Hardware Pack OPERATOR’S Position See FigUnpacking Carton See Fig Install Handle See Figs , 4,Connect Shift ROD See Fig Attach Clutch Cable See FigRemove Tiller from Crate Check Tire PressureMeets Ansi Safety Requirements OperationKnow Your Tiller Tine Operation with Wheel Drive HOW to USE Your TillerForward Wheels ONLY/TINES Stopped Reverse Wheels ONLY/TINES StoppedCultivating TurningTo Transport Before Starting EngineADD Gasoline To Start EngineTilling Hints See Fig Adjust Wheels for Cultivating See Figs Maintenance Schedule MaintenanceGeneral Recommendations Lubrication Chart Before Each USEEngine AIR Filter See FigTo Change Engine OIL See Figs Cooling System See Fig CleaningMuffler Spark PlugService and Adjustments TillerTire Care To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTine Replacement See Figs , 28 To Adjust Carburetor To Adjust Throttle Control Cable See FigOther StorageFuel System Engine OILConditions Shear pins broken Replace shear pinsGround too wet Wait for more favorable soil conditions Drive control bar is not engaged Engage drive controlLimited Warranty Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Ontario Mississauga 3E4 L5VWay Fox Terry Contact CanadaAvant en rotation de labourage de position la et Dépannage DE GuideCylindres EntreposageMoteur DE Huile Dalimentation SystèmeMoteur Réglages ET RévisionCarburateur LE Régler Pour 30 .FIG29 et 28, 27, .fig les Voir Fraises DES Remplacement17 29 .FIG 28 .FIG26 et 25 .fig les Voir Fig la Voir Terre À D’ENTRAÎNEMENT Courroie LA RéglerCourroie LA Remplacer Pour Terre À D’ENTRAÎNEMENTFig la Voir Roue LA Enlever Pour Fig la Voir Roiecour DE Protecteur LE Enlever PourFig la Voir Guidon DU Hauteur LA Régler Pour’ALLUMAGE Bougie EntretienSilencieux Refroidissement DE SystèmeLubrification Fig la Voir AIR À Filtre21 .FIG 20 et 19 .fig les VoirLubrification DE Tableau ’ENTRETIEN CalendrierUtilisation Chaque Avant Utilisation 18 et 17 .figBinage Labourage DE Conseils Fig la Voir Moteur LE Démarrer Pour’ESSENCE Réservoir LE Remplir 14 .FIG’HUILE Moteur LE Remplir Extérieurs Latéraux DéflecteursTransporter Pour CultiverMoto Votre Utiliser Comment BineuseLES Changer DE Difficile C’EST LES Seulement ROUES-AVANT MarcheMotobineuse Votre Moteur le rermardé de permet Recul Démarrage DE PoignéeRéglages différents Fig la Voir Setesvi MontageEt 4, 3, .fig les Voir Poignee LA InstallerFig la Voir Carton LE Deballer Coupez poignée, la de l’ensemble teniez vous que PendantFig la Voir D’OPERATEUR Position Pièces DES SAC DU ContenuMontage LE Pour Exiges Outils LES De Clé 1 Pince 1 pneu à Manomètre 1 usage tout à CouteauSommaire Client DU ResponsabilitésRègles les toujours Observez .motobineuse votre Entreposage ET Entretien Sécurité DE RèglesMotobineuses des Sécurité toute En lUtilisation pour ConseilsImportant Manuel

410237, 96092001000 specifications

The Poulan 96092001000,410237 is a premium chainsaw that has garnered attention from both amateur and professional users for its powerful performance and reliability. This model is designed for a variety of cutting tasks, making it suitable for everything from pruning trees to felling larger timber.

One of the standout features of the Poulan 96092001000 is its robust engine. The chainsaw is powered by a reliable two-stroke engine that delivers substantial horsepower, allowing for efficient cutting. Its engine is designed for reduced emissions, aligning with environmental standards while still providing the necessary power to handle tough jobs. Additionally, the starter mechanism is user-friendly, enabling users to start the saw effortlessly, even in cold conditions.

The chainsaw is equipped with a high-quality, durable chain that ensures smooth cutting through wood. Its bar length strikes a balance between maneuverability and cutting capacity. This makes the Poulan ideal for both detailed work in tight spaces and more extensive cutting tasks. The sharp chain is designed to self-lubricate, reducing wear and ensuring longevity, which is a vital aspect for those who intend to use the saw regularly.

Safety is paramount in chainsaw design, and the Poulan 96092001000 does not disappoint. It features a chain brake that activates when sudden pressure is applied, stopping the chain instantly to prevent accidents. The ergonomic handle design enhances user comfort and control, reducing fatigue during prolonged use. Additionally, the anti-vibration system significantly reduces handle vibrations, making it easier to control the saw over extended periods.

Another notable technology is the easy-access air filter and fuel system, which simplifies maintenance tasks. Users can quickly access these components for cleaning or replacement, contributing to the tool's longevity and performance consistency.

In summary, the Poulan 96092001000,410237 is a feature-rich chainsaw designed for both performance and user convenience. With its powerful engine, reliable cutting capabilities, superior safety features, and user-friendly maintenance options, this chainsaw is an excellent choice for anyone looking for a dependable cutting tool. Whether for professional forestry work or weekend gardening projects, the Poulan 96092001000 stands out as a top contender in its class, making it a worthwhile investment for both hobbyists and professionals alike.
Top Page Image Contents