Poulan 190388 owner manual Tine Shear Pins, Adjust Wheels for Cultivating See Figs

Page 11

OPERATION

TINE SHEAR PINS

The tine assemblies on your tiller are secured to the tine shaft with shear pins (See “TINE REPLACEMENT” in the Service and Adjustments section of this manual).

If the tiller is unusually overloaded or jammed, the shear pins are designed to break before internal damage occurs to the transmission.

•If shear pin(s) break, replace only with those shown in the Repair Parts section of this manual.

CULTIVATING

Cultivating is destroying the weeds between rows to pre- vent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil. Best digging depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields to protect small plants from being buried.

•Cultivate up and down the rows at a speed which will allow tines to uproot weeds and leave the ground in rough condition, promoting no further growth of weeds and grass (See Fig. 15).

FIG. 15

ADJUST WHEELS FOR CULTIVATING (See Figs. 16 and 17)

•Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel.

•Move wheel outward approximately 1 inch (2.5 cm) until hole in inner wheel hub lines up with inner hole in axle.

•Replace clevis pin and hairpin clip on inside of wheel and remove blocks.

•Repeat preceding steps on left hand side.

NOTE: In extremely rough conditions and while cultivat- ing, the wheels should be moved outward on the axle for increased stability.

OUTER VIEW OF TIRE

CLEVIS

PIN

tire_1

HAIRPIN

 

CLIP

FIG. 16

INNER VIEW OF TIRE

CLEVIS

PIN

HAIRPIN

CLIP

tire_2

FIG. 17

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model NO. HDR500M Preparation Safety RulesMaintenance and Storage TrainingTable of Contents OPERATOR’S Position See Fig AssemblyTools Required for Assembly Unpacking Carton See Fig Install Handle See Figs , 4,Check Tire Pressure Attach Clutch Cable See FigConnect Shift ROD See Fig Remove Tiller from CrateKnow Your Tiller Meets Ansi Safety RequirementsOperation Reverse Wheels ONLY/TINES Stopped HOW to USE Your TillerTine Operation with Wheel Drive FORWARD- Wheels ONLY/TINES StoppedADD Gasoline Before Starting EngineTurning To TransportTilling Hints To Start Engine See FigCultivating Tine Shear PinsAdjust Wheels for Cultivating See Figs General Recommendations MaintenanceMaintenance Schedule AIR Filter See Fig EngineCooling System See Fig CleaningMuffler Spark PlugTire Care Service and AdjustmentsTo Adjust Handle Height See Fig TillerTine Replacement See Figs , 25 To Replace Ground Drive Belt See Figs Ground Drive Belt Adjustment See FigTo Remove Belt Guard See Fig To Adjust Carburetor To Adjust Throttle Control Cable See FigEngine OIL StorageOther Fuel SystemTroubleshooting Points Limited Warranty

190388 specifications

The Poulan 190388 is a powerful and versatile tool designed to meet the demands of homeowners and landscaping professionals alike. Renowned for its dependability and performance, this lawn care equipment stands out in the market for several compelling reasons.

One of the main features of the Poulan 190388 is its robust 42cc engine. This two-cycle engine delivers ample power to tackle a variety of yard tasks ranging from trimming lawns to enhancing garden aesthetics. Its design prioritizes efficiency, ensuring that users can complete their tasks without frequent interruptions for refueling.

The Poulan 190388 is equipped with a specially designed cutting system that ensures precision and efficiency. Its 18-inch cutting blade guarantees optimal coverage and reduces the time needed for mowing or trimming. The sharp edge of the blade allows for a clean cut, promoting healthier grass growth and enhancing the overall appearance of the lawn.

A significant advantage of this tool is its lightweight design. Weighing approximately 10 pounds, the Poulan 190388 is easy to maneuver, making it an ideal choice for users of all experience levels. Its ergonomic handle offers a comfortable grip, allowing prolonged use without causing fatigue, thereby increasing productivity during long work sessions.

The Poulan 190388 incorporates advanced technologies, including an easy-start mechanism that reduces the resistance typically associated with starting two-cycle engines. This feature ensures that the equipment can be fired up easily, even for users who may not have extensive experience with lawn care tools.

Durability is another hallmark of the Poulan 190388. Constructed from high-quality materials, this lawn care equipment is designed to withstand the wear and tear of regular use. Its robust build not only enhances its lifespan but also decreases the likelihood of maintenance issues, allowing users to focus more on their lawn care tasks rather than repairs.

Additional features of the Poulan 190388 include adjustable cutting heights, allowing users to tailor the height of their cut according to their specific needs. This flexibility makes it suitable for various grass types and terrains, ensuring that it meets diverse landscaping demands.

In summary, the Poulan 190388 stands out for its powerful engine, lightweight design, innovative technologies, and robust durability. Whether for maintaining a manicured lawn or tackling rough terrain, it proves to be an essential tool for achieving a beautiful landscape. With its combination of efficiency and user-friendly features, the Poulan 190388 is a smart investment for anyone looking to elevate their lawn care game.
Top Page Image Contents