Troy-Bilt 630C-Tuffy manual Clearing the Tines, Loading and Unloading the Tiller

Page 16

TILLING TIPS & TECHNIQUES (CON’T)

Terrace Gardening (continued)

• To create a terrace, start at the top of the slope and work down. Go back and forth across the first row as shown in Fig. 4-10.

• Each succeeding lower terrace is started by walking below the terrace you’re pre- paring. For added stability of the tiller, always keep the uphill wheel in the soft, new- ly tilled soil. Do not till the last 12" or more of the downhill outside edge of each terrace. This untilled strip helps prevents the terraces from breaking apart and washing downhill. It also provides a walking path between rows.

Fig. 4-10

Clearing the Tines

The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may be- come tangled. Follow these procedures to help avoid tangling and to clean the tines, if necessary.

•To reduce tangling, set the depth regulator deep enough to get maximum “chopping” action as the tines chop the material against the ground. Also, try to till under crop residues or cover crops while they are green, moist and tender.

•While power composting, try swaying the handlebars from side to side (about 6" to 12"). This “fishtailing” action often clears the tines of debris.

•If tangling occurs, lift the tines out of the soil and run the tiller in reverse (if unit is equipped with powered reverse) for a few feet. This reversing action should unwind a good deal of debris.

•It may be necessary to remove the debris by hand (a pocket knife will help you to cut away the mate- rial). Be sure to stop the engine and disconnect the spark plug wire before clearing the tines by hand.

WARNING: Before clearing the tines by hand, stop the engine, allow all moving parts to stop and disconnect the spark plug wire. Remove the ignition key on electric start models.

Failure to follow this warning could result in personal injury.

LOADING AND UNLOADING THE TILLER

WARNING: Loading and unloading the tiller into a vehicle is potentially hazardous and we don’t recommend doing so unless absolutely necessary, as this could result in personal injury or property damage. However, if you must load or unload the tiller, follow the guidelines given next.

•Before loading or unloading, stop the en- gine, wait for all parts to stop moving, disconnect the spark plug wire and let the engine and muffler cool.

•The tiller is too heavy and bulky to lift

safely by one person. Two or more people should share the load.

•Use sturdy ramps and manually (engine shut off) roll the tiller into and out of the vehicle. Two or more people are needed to do this.

•The ramps must be strong enough to support the combined weight of the tiller and any handlers. The ramps should pro- vide good traction to prevent slipping; they should have side rails to guide the tiller along the ramps; and they should have a locking device to secure them to the vehicle.

•The handlers should wear sturdy footwear that will help to prevent slipping.

•Position the loading vehicle so that the ramp angle is as flat as possible (the less incline to the ramp, thebetter). Turn the vehicle’s engine off and apply its parking brake.

•When going up ramps, stand in the

normal operating position and push the

tiller ahead of you. Have a person at each side to turn the wheels.

•When going down ramps, walk back- ward with the tiller following you. Keep alert for any obstacles behind you. Posi- tion a person at each wheel to control the speed of the tiller. Never go down ramps tiller-first, as the tiller could tip forward.

•Place wooden blocks on the downhill side of the wheels if you need to stop the tiller from rolling down the ramp. Also, use the blocks to temporarily keep the tiller in place on the ramps (if necessary), and to chock the wheels in place after the tiller is in the vehicle.

•After loading the tiller, prevent it from rolling by engaging the wheels in the WHEEL DRIVE position. Chock the wheels with blocks and securely tie the tiller down.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Form no -10594D.fm 11/19/03Finding Model Number Table of ContentsCustomer Support Safety Safety Alert SymbolKeep children and pets away Exercise caution to avoid slipping or fall- ingUse slower engine speeds Operating Symbols To Avoid Serious InjuryAssembly Assembly StepsIntroduction Inspect UnitInstall Forward Clutch Cable Use the handlebar to roll the tiller to a flat areaWhile preventing the cable adjuster Outermost coil to the outermost coilFrom turning If the spring length is incorrect, youCheck Transmission OIL Level Check all nuts and screws for tightnessAture package to identify the controls on your engine FreewheelTravel Position Shallow Settings To adjust the handlebarsTo operate the Forward Clutch Bail Stop all tiller motion by releasing the Forward Clutch BailStarting and Stopping Introduction BREAK-IN OperationChange engine oil Operating the Tiller Stopping the Engine and TillerFor forward motion of the wheels and tines To move the Model 630C in reverse for short distancesTilling Tips & Techniques Tilling Tips & Techniques CON’T Power CompostingTilling On Slopes Clearing the Tines Loading and Unloading the TillerTransmission Gear OIL Service Tiller LubricationCheck Hardware Check Tire PressureRemoving⁄Installing a Single Tine Removing⁄Installing a Tine AssemblyBolo Tines Tine InspectionReplacement Belt Information Checking and AdjustingTo Check Forward Belt Tension Forward Clutch Bail Adjustment Engine Cleaning AIR Cleaner Service Engine OIL ServiceModels 634F/634A only To Check Reverse Belt TensionSpark Plug Service Spark Arrester Screen ServiceOFF-SEASON Storage To Change the Engine OilTroubleshooting Problem Possible Cause CorrectionModels 630C, 634F & 634A Parts List DescriptionModels 630C, 634F & 634A 1916719 For Model 630C For Model 634F For Model 634A Front 619-04013 Tine Shaft Hold Tines With Blunt End Toward You37 a For Model 630C For Model 634F For Model 634A TROY-BILT Tiller Lifetime Limited Warranty

630C-Tuffy specifications

The Troy-Bilt 630C-Tuffy stands out as a reliable and robust garden tiller designed for homeowners and gardening enthusiasts looking to cultivate their gardens with ease. This tiller is particularly noted for its performance, durability, and user-friendly features, making it a favored choice among many.

One of the most prominent characteristics of the 630C-Tuffy is its powerful 208cc engine, which provides ample power for breaking up hard soil, turning compacted ground, and mixing in compost or fertilizers. This engine ensures that the tiller can handle a variety of tasks, from light tilling in a small garden to more demanding projects. The tiller features a 16-inch tilling width, allowing users to cover a significant area in a shorter amount of time while the adjustable tilling depth can be set from 1 to 7 inches to suit specific gardening needs.

A standout technology utilized in the Troy-Bilt 630C-Tuffy is its Counter-Rotating Tines (CRT). This innovation allows the tines to turn in the opposite direction of the wheels, creating a more effective and efficient tilling action. This design not only aids in breaking up the soil more thoroughly but also reduces the likelihood of the tiller becoming bogged down in tougher soil conditions.

The tiller is built with a sturdy steel frame and heavy-duty tines that ensure longevity and reliability even with repeated use. Its 6-position adjustable handle offers comfortable operation, enabling users to customize the height according to their preference, which helps reduce fatigue during long tilling sessions. Moreover, the Troy-Bilt 630C-Tuffy is equipped with a bump start feature, making it easy to start and operate.

For added convenience, this tiller features large, durable wheels that enhance maneuverability across various terrains, providing improved stability and traction. The 630C-Tuffy also boasts a folding handle for easier storage, allowing users to save space in their garages or sheds when not in use.

In summary, the Troy-Bilt 630C-Tuffy combines power, technology, and user-friendly features to deliver a top-tier gardening tool. With its ergonomic design, efficient tilling capabilities, and strong build, it is a valuable addition to any garden enthusiast's toolkit, ready to turn soil and nurture thriving gardens.
Top Page Image Contents