Troy-Bilt 630C-Tuffy manual Check Transmission OIL Level, Check all nuts and screws for tightness

Page 9

STEP 6: CHECK TRANSMISSION OIL LEVEL

The transmission was filled with gear oil at the factory. However, you should check the gear oil level at this time to make certain it is correct.

IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmission com- ponents.

1.With the tiller on level ground, pull the Depth Regulator Lever (FF, Fig. 2-10) back and then all the way up until the lowest notch in the lever is engaged.

2.Remove the oil fill plug (GG, Fig. 2-11) from the transmission housing cover and locate the main drive shaft situated inside the housing.

3.The gear oil level is correct if the gear oil is approximately halfway up the side of the main drive shaft.

4.If the oil level is low, add gear oil by re- ferring to A. To Check the Transmission Gear Oil Level in Section 5.

FF

STEP 7: ADD MOTOR OIL

The tiller is shipped without oil in the en- gine.

IMPORTANT: Do not start the engine with- out first adding motor oil. Severe engine damage will result if the engine is run with- out oil.

1.Refer to the separate Engine Owner’s Manual for engine oil specifications and capacities.

2.With the tiller on level ground, move the Depth Regulator Lever (FF, Fig. 2-10) up or down until the engine is level.

3.Add motor oil as described in the En- gine Owner’s Manual.

4.Move the Depth Regulator Lever all the way down until the highest notch is en- gaged. This places the tines in the “travel” position, which allows the tiller to be moved without the tines touching the ground.

STEP 8: CHECK HARDWARE

Check all nuts and screws for tightness.

STEP 9: CHECK AIR PRESSURE IN TIRES (units with pneumatic tires)

Check the air pressure with a tire gauge. Deflate or inflate the tires equally to be- tween 15 PSI and 20 PSI (pounds per square inch). Be sure that both tires are in- flated equally or the unit will pull to one side.

Fig. 2-10: Adjust Depth Regulator Lever.

GG

Fig. 2-11: Remove gear oil fill plug.

IMPORTANT: This completes the assembly steps. Before operating your tiller, make sure you read the following sections in this Manual, as well as the separate Engine Owner’s Manual:

•Section 1: Safety

•Section 3: Features and Controls

•Section 4: Operation

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 11/19/03 Form no -10594D.fmTable of Contents Finding Model NumberCustomer Support Safety Alert Symbol SafetyExercise caution to avoid slipping or fall- ing Keep children and pets awayUse slower engine speeds To Avoid Serious Injury Operating SymbolsAssembly Steps AssemblyIntroduction Inspect UnitUse the handlebar to roll the tiller to a flat area Install Forward Clutch CableOutermost coil to the outermost coil While preventing the cable adjusterFrom turning If the spring length is incorrect, youCheck all nuts and screws for tightness Check Transmission OIL LevelFreewheel Ature package to identify the controls on your engineTo adjust the handlebars Travel Position Shallow SettingsTo operate the Forward Clutch Bail Stop all tiller motion by releasing the Forward Clutch BailIntroduction BREAK-IN Operation Starting and StoppingChange engine oil Stopping the Engine and Tiller Operating the TillerFor forward motion of the wheels and tines To move the Model 630C in reverse for short distancesTilling Tips & Techniques Power Composting Tilling Tips & Techniques CON’TTilling On Slopes Loading and Unloading the Tiller Clearing the TinesTiller Lubrication Transmission Gear OIL ServiceCheck Hardware Check Tire PressureRemoving⁄Installing a Tine Assembly Removing⁄Installing a Single TineBolo Tines Tine InspectionChecking and Adjusting Replacement Belt InformationTo Check Forward Belt Tension Engine Cleaning AIR Cleaner Service Engine OIL Service Forward Clutch Bail AdjustmentModels 634F/634A only To Check Reverse Belt TensionSpark Arrester Screen Service Spark Plug ServiceOFF-SEASON Storage To Change the Engine OilProblem Possible Cause Correction TroubleshootingDescription Models 630C, 634F & 634A Parts ListModels 630C, 634F & 634A 1916719 For Model 630C For Model 634F For Model 634A Front 619-04013 Hold Tines With Blunt End Toward You Tine Shaft37 a For Model 630C For Model 634F For Model 634A TROY-BILT Tiller Lifetime Limited Warranty

630C-Tuffy specifications

The Troy-Bilt 630C-Tuffy stands out as a reliable and robust garden tiller designed for homeowners and gardening enthusiasts looking to cultivate their gardens with ease. This tiller is particularly noted for its performance, durability, and user-friendly features, making it a favored choice among many.

One of the most prominent characteristics of the 630C-Tuffy is its powerful 208cc engine, which provides ample power for breaking up hard soil, turning compacted ground, and mixing in compost or fertilizers. This engine ensures that the tiller can handle a variety of tasks, from light tilling in a small garden to more demanding projects. The tiller features a 16-inch tilling width, allowing users to cover a significant area in a shorter amount of time while the adjustable tilling depth can be set from 1 to 7 inches to suit specific gardening needs.

A standout technology utilized in the Troy-Bilt 630C-Tuffy is its Counter-Rotating Tines (CRT). This innovation allows the tines to turn in the opposite direction of the wheels, creating a more effective and efficient tilling action. This design not only aids in breaking up the soil more thoroughly but also reduces the likelihood of the tiller becoming bogged down in tougher soil conditions.

The tiller is built with a sturdy steel frame and heavy-duty tines that ensure longevity and reliability even with repeated use. Its 6-position adjustable handle offers comfortable operation, enabling users to customize the height according to their preference, which helps reduce fatigue during long tilling sessions. Moreover, the Troy-Bilt 630C-Tuffy is equipped with a bump start feature, making it easy to start and operate.

For added convenience, this tiller features large, durable wheels that enhance maneuverability across various terrains, providing improved stability and traction. The 630C-Tuffy also boasts a folding handle for easier storage, allowing users to save space in their garages or sheds when not in use.

In summary, the Troy-Bilt 630C-Tuffy combines power, technology, and user-friendly features to deliver a top-tier gardening tool. With its ergonomic design, efficient tilling capabilities, and strong build, it is a valuable addition to any garden enthusiast's toolkit, ready to turn soil and nurture thriving gardens.
Top Page Image Contents