Troy-Bilt 634K--ProLine manual Install Forward Clutch Cable, T T U

Page 7
STEP 4: INSTALL FORWARD CLUTCH CABLE

K

 

 

G

H

 

I

A

 

 

F

 

 

 

 

G

 

 

E

F

C

 

 

 

 

 

J

D

 

 

 

 

B

Fig. 2.2: Attach handlebar.

M

O

N

L

Fig. 2-3: Wheel in FREEWHEEL position

STEP 4: INSTALL FORWARD CLUTCH CABLE

1.Carefully unwrap the forward clutch ca- ble (cable without an attached knob) from its shipping position and slide the thin ca- ble wire (T, Fig. 2-4) into the slot in the ca- ble bracket. Push the cable connector (U, Fig. 2-4) up through the hole in the bracket until the groove in the connector snaps into place.

2.Thread the #10-24 hex nut (Z, Fig. 2-5) halfway onto the screw (V) which runs through the spring (W, Fig. 2-5).

3.Thread the screw (V) into the cable ad- juster (X).

drive pin (M) through the wheel shaft only (not through the wheel hub). Secure the wheel drive pin with the hairpin cotter (L), pushing the hairpin cotter in as far as it will go. The wheel should now spin freely (freewheel) on the wheel shaft. Repeat with the other wheel.

4.Use the handlebar to roll the tiller to a flat area.

IMPORTANT: Before starting the engine, the wheels must be placed in the WHEEL DRIVE position (pins through wheel hubs and wheel shaft). This procedure is described in Wheel Drive Pins in Section 3.

T

T

T U

Fig. 2-4: Installing forward clutch cable bracket and cable.

7

Image 7
Contents Troy-BiltLLC, P.O. BOX 361131 CLEVELAND, OHIO Operator’s ManualRear-tineTiller Models 630C-Tuffy 634A-SuperBroncoTM 634K-ProLineCUSTOMER SUPPORT TABLE OF CONTENTSContent FINDING MODEL NUMBERPreparation SECTION 1 SAFETYSafety Alert Symbol Trainingc.Use slower engine speeds Maintenance and StorageDecals Operating SymbolsTO AVOID SERIOUS INJURY Hardware bag contents SECTION 2 ASSEMBLYLoose Parts List ASSEMBLY STEPST T U STEP 4 INSTALL FORWARD CLUTCH CABLEPage STEP 8 CHECK HARDWARE Section 3 Features and ControlsSTEP 6 CHECK TRANSMISSION OIL LEVEL STEP 7 ADD MOTOR OILINTRODUCTION SECTION 3 FEATURES AND CONTROLSWHEEL DRIVE PINS WARNING BeforeFORWARD CLUTCH BAIL HANDLEBAR HEIGHT ADJUSTMENTSettings To adjust the handlebarsSTARTING AND STOPPING Pre-StartChecklist1.Complete the Pre-StartChecklist on this page BREAK-INOPERATIONStopping the Engine and Tiller OPERATING THE TILLERStopping the Tiller and Engine Avoid Making Footprints TILLING TIPS & TECHNIQUESTilling Depths Let the Tiller Do the WorkWARNING Do not Power CompostingTILLING TIPS & TECHNIQUES CON’T Tilling On SlopesLOADING AND UNLOADING THE TILLER Clearing the TinesTerrace Gardening continued PROCEDURE SECTION 5 MAINTENANCETRANSMISSION GEAR OIL SERVICE MAINTENANCE SCHEDULEB B A B. Removing⁄Installing a Single TineC. Removing⁄Installing a Tine Assembly BOLO TINESTo Check Forward Belt Tension CHECKING AND ADJUSTINGReplacement Belt Information FORWARD DRIVE BELT TENSIONENGINE OIL SERVICE FORWARD CLUTCH BAIL ADJUSTMENTENGINE CLEANING AIR CLEANER SERVICECARBURETOR/GOVERNOR CONTROL ADJUSTMENTS SPARK PLUG SERVICESPARK ARRESTER SCREEN SERVICE THROTTLE LEVER ADJUSTMENTCORRECTION TROUBLESHOOTINGPROBLEM POSSIBLE CAUSEDESCRIPTION SECTION 6 MODELS 630C, 634A & 634K PARTS LISTMODELS 630C, 634A & 634K DESCRIPTION MODELS 630C, 634A & 634KDESCRIPTION DESCRIPTION FRONT DESCRIPTION RIGHT-HANDTINE TINE SHAFTWHEEL SHAFT 15 28 MODELS 630C, 634A & 634K TROY-BILTTILLER LIFETIME LIMITED WARRANTY