Troy-Bilt 634K--ProLine Tilling Tips & Techniques Con’T, Power Composting, Tilling On Slopes

Page 15
TILLING TIPS & TECHNIQUES (CON’T)

TILLING TIPS & TECHNIQUES (CON’T)

Power Composting

Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will de- compose during the non-growing season and add important natural nutrients to the soil.

The first place to begin is with crop residues such as leftover vines, stalks, stems and roots. Power compost these crop residues as soon as they finish bearing. The sooner this is done, the better, as tender green matter is easier to till under. Use the deepest depth regulator set- ting possible without causing the engine to labor or the tiller to jump ahead.

Standing cornstalks of reasonable height can be power composted. Pushing over (but not uprooting) cornstalks will often make it easier to chop up the stalks. Keep the tines clear of excessive tangling by “fishtailing” or frequently using reverse. Make several passes, then re- turn a few days later to finish off any remaining stubble.

After tilling under crop residues, add more organic matter such as leaves, grass clippings and even kitchen scraps. When tilled into the soil, this organic matter will decompose and add even more important nutrients to the soil.

WARNING: When power composting, do not keep the Depth Regulator Lever at a deep setting if the tiller jumps or bucks.

If jumping or bucking occurs, move the Depth Regulator Lever down to a shallow setting and then slowly increase the tilling depth on later passes.

Failure to follow this warning could result in personal injury.

After power composting, you may want to plant a “green manure” cover crop to protect the soil during the off-season. You simply grow a crop of clover, alfalfa, buckwheat, peas, beans, rye grass, grain, or kale and then till it into the soil prior to the planting season.

Tilling On Slopes

Read the following recommendations before tilling on slopes:

If you must garden on a moderate slope, please follow two very important guidelines:

1.Till only on moderate slopes, never on steep ground where footing is difficult (review safe- ty rules in Section 1: Safety of this manual).

2.We recommend tilling up and down slopes rather than terracing. Tilling vertically on a slope allows maximum planting area and also leaves room for cultivating.

IMPORTANT: When tilling on slopes, be sure the correct oil level is maintained in the engine (check every one-half hour of operation). The incline of the slope will cause the oil to slant away from its normal level and this can starve engine parts of required lubrication. Keep the motor oil level at the full point at all times!

Tilling Up and Down Slopes (Vertical Tilling)

WARNING: Do not

operate tiller on a slope too steep for safe operation. Till slowly and be sure you have good footing. Never permit tiller to freewheel down slopes. Failure to follow this warning could result in personal injury.

To keep soil erosion to a minimum, be sure to add enough organic matter to the soil so that it has good moisture-holding texture and try to avoid leaving footprints or wheel marks.

When tilling vertically, try to make the first pass uphill as the tiller digs more deeply going uphill than it does downhill. In soft soil or weeds, you may have to lift the handlebars slightly while going uphill. When going downhill, overlap the first pass by about one-half the width of the tiller.

Tilling Across Slopes Without Using Terraces (Horizontal Tilling)

If vertical or terracing gardening aren’t practical for you, then you can till laterally across a slope. We don’t recommend this method as it can create unsure footing and invites soil erosion.

As in terrace gardening, start at the top of the slope and overlap the first pass by half the width of the tiller. For added stability of the tiller, always keep the uphill wheel in the soft, newly tilled soil.

Terrace Gardening

When a slope is too steep or too short for vertical tilling, it may be necessary to till across the slope and create terraced rows. Terraces are rows that are cut into the side of a slope, creating a narrow, but flat area on which to plant.

On a long slope, you can make several terraces, one below the other.

Terraces should be only 2-to-3 feet wide. Digging too far into the side of the slope will expose poor subsoil that is unproductive for plants.

15

Image 15
Contents Troy-BiltLLC, P.O. BOX 361131 CLEVELAND, OHIO Operator’s ManualRear-tineTiller Models 630C-Tuffy 634A-SuperBroncoTM 634K-ProLineCUSTOMER SUPPORT TABLE OF CONTENTSContent FINDING MODEL NUMBERPreparation SECTION 1 SAFETYSafety Alert Symbol Trainingc.Use slower engine speeds Maintenance and StorageOperating Symbols DecalsTO AVOID SERIOUS INJURY Hardware bag contents SECTION 2 ASSEMBLYLoose Parts List ASSEMBLY STEPST T U STEP 4 INSTALL FORWARD CLUTCH CABLEPage STEP 8 CHECK HARDWARE Section 3 Features and ControlsSTEP 6 CHECK TRANSMISSION OIL LEVEL STEP 7 ADD MOTOR OILINTRODUCTION SECTION 3 FEATURES AND CONTROLSWHEEL DRIVE PINS WARNING BeforeFORWARD CLUTCH BAIL HANDLEBAR HEIGHT ADJUSTMENTSettings To adjust the handlebarsSTARTING AND STOPPING Pre-StartChecklist1.Complete the Pre-StartChecklist on this page BREAK-INOPERATIONOPERATING THE TILLER Stopping the Engine and TillerStopping the Tiller and Engine Avoid Making Footprints TILLING TIPS & TECHNIQUESTilling Depths Let the Tiller Do the WorkWARNING Do not Power CompostingTILLING TIPS & TECHNIQUES CON’T Tilling On SlopesClearing the Tines LOADING AND UNLOADING THE TILLERTerrace Gardening continued PROCEDURE SECTION 5 MAINTENANCETRANSMISSION GEAR OIL SERVICE MAINTENANCE SCHEDULEB B A B. Removing⁄Installing a Single TineC. Removing⁄Installing a Tine Assembly BOLO TINESTo Check Forward Belt Tension CHECKING AND ADJUSTINGReplacement Belt Information FORWARD DRIVE BELT TENSIONENGINE OIL SERVICE FORWARD CLUTCH BAIL ADJUSTMENTENGINE CLEANING AIR CLEANER SERVICECARBURETOR/GOVERNOR CONTROL ADJUSTMENTS SPARK PLUG SERVICESPARK ARRESTER SCREEN SERVICE THROTTLE LEVER ADJUSTMENTCORRECTION TROUBLESHOOTINGPROBLEM POSSIBLE CAUSEDESCRIPTION SECTION 6 MODELS 630C, 634A & 634K PARTS LISTMODELS 630C, 634A & 634K MODELS 630C, 634A & 634K DESCRIPTIONDESCRIPTION MODELS 630C, 634A & 634K FRONT MODELS 630C, 634A & 634K TINE SHAFT RIGHT-HANDTINEWHEEL SHAFT 15 28 MODELS 630C, 634A & 634K TROY-BILTTILLER LIFETIME LIMITED WARRANTY