To Stop Engine, Using Your Tiller, Models 343

•Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. Do not let starter handle snap back against starter.

•Repeat preceding instructions 5 and 6 until engine starts. When engine starts, move choke lever on engine halfway between CHOKE and RUN.

•Move throttle control to IDLE position for a few minutes warm-up. Move choke lever to RUN position as engine warms up.

Models 343 & 345

•Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug.

•Make certain all controls are in the neutral position (released). See Figure 6.

•Place the engine speed control in the START position.

•Push primer two (2) or three (3) times See Figure 10. Wait about two (2) seconds between each push.

NOTE: Primer may be needed to restart a warm engine after a short shutdown.

•Stand at side of tiller. Grasp the starter handle and pull out slowly, until it pulls slightly harder. Let rope rewind slowly.

•Pull rope with a rapid full arm stroke. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.

NOTE: If engine fails to start after three (3) pulls, push primer two (2) times and pull starter rope again.

•Repeat steps 4 and 5 until engine starts. Refer to engine manual for additional engine information.

NOTE: After starting engine and prior to using the tiller, be certain to check the clutch adjustment as described in “Checking the Clutch Adjustment” section of the Assembly Instructions.

To Stop Engine

•Move throttle control lever to STOP or OFF position.

•Disconnect spark plug wire from spark plug and ground against the engine to prevent accidental starting while equipment is unattended.

Using Your Tiller

Your tiller is a precision built machine designed for seed bed preparation, cultivating, furrowing and mulching. It is engineered to minimize the hardest work in the vegetable or flower garden, to till the soil for planting and cultivating, and to perform many other useful labor saving tasks in the garden.

With the proper amount of care and maintenance, this machine will provide the owner with many years of service.

Wheel Position

The tiller is shipped with the wheels adjusted such that the unit sits level. While tilling, as the tines enter the ground and the front of the tiller lowers, the wheels must be raised to level the unit, which is essential for proper engine operation. This adjustment is made by removing the clevis pin and hairpin clip from wheel yoke, raising the wheels to the desired height, and replacing the clevis pin and hairpin clip. See Figure 9.

Depth Stake

Wheel

Yoke

Hairpin

Clip and

Clevis Pin

Figure 9

Removing End Caps (Model 390 only)

The end cap, which are used to avoid tilled soil from overflowing onto unwanted areas, are removable from the outer axle. Remove the hairpin clip and clevis pin that is securing each end cap and slide end cap off the axle. See Figure 10.

End Cap

Clevis Pin	Hairpin Clip

Figure 10

390 Shown specifications

The MTD 390 is a notable product in the range of powerful and efficient garden tools designed for both professional landscapers and avid gardeners. This versatile machine is engineered to tackle various landscaping tasks with precision and ease. Its combination of robust design, cutting-edge technologies, and user-friendly features make it an essential tool for maintaining pristine gardens and outdoor spaces.

At the heart of the MTD 390 is its powerful engine that provides reliable performance. The engine is designed for optimal efficiency, ensuring that users can complete their tasks without unnecessary downtime. With a displacement that allows for high torque and consistent power delivery, the MTD 390 easily handles thick grass and dense foliage.

One of the standout features of the MTD 390 is its advanced blade technology. The cutting deck is equipped with precision-engineered blades that provide a clean and even cut, promoting healthy growth in lawns and gardens. The adjustable cutting height allows users to customize their mowing experience, accommodating different grass types and seasonal requirements. This flexibility ensures that every user can achieve the desired lawn appearance.

In addition to its cutting capabilities, the MTD 390 emphasizes comfort and usability. The ergonomic handle design minimizes strain during operation, allowing for extended periods of use without discomfort. The lightweight construction of the machine makes it easy to maneuver, even in tight spaces. Features such as quick-release systems for the cutting deck further enhance the convenience, making maintenance straightforward.

Technology plays a crucial role in the MTD 390's functionality. The machine is equipped with innovative start systems that ensure a swift ignition process, eliminating the frustrations often associated with traditional pull-start mechanisms. Furthermore, the design incorporates efficient fuel consumption, minimizing operating costs while maintaining powerful performance.

Durability is another key characteristic of the MTD 390. The robust frame and high-quality materials used in its construction ensure that it withstands the rigors of frequent use. Whether dealing with challenging terrains or changing weather conditions, the MTD 390 is built to endure, making it a long-term investment for users.

In summary, the MTD 390 stands out as a premium choice for anyone looking to enhance their gardening experience. Its powerful engine, advanced cutting technology, ergonomic design, and durable construction make it a reliable companion for achieving beautiful outdoor spaces. Whether you're a professional landscaper or a weekend warrior, the MTD 390 is equipped to handle all your gardening needs with efficiency and ease.