MTD 12211, 12212 Introduction, Inspect Unit, Hardware BAG Parts List, Attach Handlebars

Page 6

Section

2Assembly

WARNING

To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you

4. The tiller is heavy. You should not attempt to remove it from the shipping platform until instructed to do so in these “Assembly” steps.

1 2 3 4

56

have read and understand the safety and

HARDWARE BAG PARTS LIST

7

89

operating instructions in this Manual.

Fig.

 

Ref. Qty.

Description

11

10

INTRODUCTION

Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly.

INSPECT UNIT

Inspect the unit and carton for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the damage and request instructions for filing a claim. To protect your rights, put your claim in writing and mail a copy to the carrier within 15 days after the unit has been delivered. Contact us at the factory if you need assistance in this matter.

UNPACKING AND ASSEMBLY INSTRUCTIONS

STEP 1: UNPACKING INSTRUCTIONS

1.Remove any cardboard inserts and packaging material from the carton. Remove any staples from the bottom of the carton and remove the carton.

2.Cut the large, plastic tie strap that secures the transmission tube to the ship- ping pallet. Leave the handlebars on top of the tiller to avoid damaging any cables.

3. A bag with loose hardware is inside the literature envelope. Check the contents against the following list and Figure 2-1. Contact your local dealer or the factory if any items are missing or damaged.

NOTE: For electric start units, a second hardware bag is located near the battery.

6

12 3/8-16 x 1" Hex Hd. Screw

21 Keyed Washer

31 Wheel Gear Lever Knob

41 Height Adjustment Flange Screw (See Figure 2-1A)

52 3/8" Flat Washer

62 #10 Lockwasher

72 3/8"-16 Nylock Lock Nut

82 #10-32 x 1/2" Round Hd. Screw

92 #10-32 Nut

101 Cotter Pin (not used)

114 Plastic Tie Strap (2 not used)

Tools/Materials Needed for Assembly

(1) 3/8" open-end wrench*

(1)7/16" open-end wrench* (electric start unit only)

(2)9/16" open-end wrench*

(1)7/8" open-end wrench or 8" long adjustable wrench

(1) Scissors (to trim plastic ties)

(1) Ruler

(1)Small board (to tap plastic knob on lever)

(1) Tire pressure gauge

(1) Clean oil funnel

(1)Clean, high-quality motor oil. Refer to the separate Engine Owner’s Manual for motor oil specifications and quantity required.

*Adjustable wrenches may be used.

IMPORTANT: Motor oil must be added to the engine crankcase before the engine is started. Follow the instructions in this “Assembly” Section and in the separate Engine Owner’s Manual.

Figure 2-1: Loose hardware (shown in reduced size).

Flange

Figure 2-1A Handlebar height adjustment uses the flange head screw.

NOTE: LEFT and RIGHT sides of the tiller are as viewed from the operator’s posi- tion behind the handlebars.

STEP 2: ATTACH HANDLEBARS

1.On electric start units, remove one screw and lockwasher from the curved height adjustment bracket (A, Figure 2-2), loosen the second screw, and swing the bracket to one side.

A

Figure 2-2: On electric start units, move height adjustment bracket aside.

2.Cut the large, plastic cable ties that secure the handlebar ends to the handle- bar mounting tabs on the transmission top cover.

3.Gently lift handlebar (do not over- stretch attached cable) and place handle- bar cross-brace (B, Figure 2-3) in front of curved height adjustment bracket (C).

Image 6
Contents 7HP Pony REAR-TINE Tiller Recoil Start Model shownSee Back Cover for Customer Service information Preparation Repairs, adjustments or inspectionsTraining OperationMaintenance and Storage Keep children and pets awayUse slower engine speeds Operating Symbols DecalsTo Avoid Serious Injury Inspect Unit Hardware BAG Parts ListIntroduction Attach HandlebarsAttach Reverse Clutch Control Cable Attach Forward Clutch Control CableADD Motor OIL to Engine Check Transmission Gear OIL LevelAttach Wheel Gear Lever Check AIR Pressure in TiresCheck Hardware for Tightness Electric Start Assembly Steps Battery Activation and ChargingAttach Battery Cables and Vent Tube Install BatteryConnect Wiring Harness KeyswitchWheel Gear Lever Engine ControlsForward Clutch Control To Operate the Forward Clutch ControlReverse Clutch Control Handlebar Height AdjustmentTo Adjust the Handlebar Height Depth RegulatorEngine Throttle Control Lever Electric Start Keyswitch Electric Start ModelEngine Controls Stop Stops the engine on recoil start models onlyEngine PRE-START ChecklistStarting and Stopping BREAK-IN OperationStopping the Engine Operating the TillerStarting the Engine Release all controls on the tillerFor reverse motion of the wheels and tines Turning the Tiller AroundFor forward motion of the wheels and tines Stopping the Tiller and EngineAvoid tilling soggy, wet soil Let the tiller do the workTilling depths Avoid making footprintsTilling on slopes Tilling across slopes without using terracesClearing the tines Tilling up and down slopesPower Composting Loading and Unloading the TillerTiller Lubrication Required Maintenance ScheduleProcedure EveryCheck Tire Pressure Transmission Gear OIL ServiceCheck Hardware Check for OIL LeaksAIR Cleaner Service Engine CleaningEngine OIL Service CARBURETOR/GOVERNOR Control AdjustmentsWheel Gear Cable Adjustment OFF Season StorageBolo Tines Checking and Adjusting Forward Clutch Belt Tension Checking and Adjusting Tension on Clutch BeltsCutting Edge Tine Checking and Adjusting Reverse Clutch Belt Tension More Belt TensionInstalling Forward Clutch Belt Removing Forward Clutch BeltInstalling Reverse Clutch Belt Removing Reverse Clutch BeltBattery Storage Battery MaintenanceBattery Care in Service Battery Removal and InstallationBumper HILLER/FURROWERROW Marker Troubleshooting Problem Possible Cause CorrectionModels 12211 Part DescriptionQTY See page 36, Ref 47, for attach Ment screw Parts List ENGINE, Support BRACKETS, PULLEYS, BELTS, Belt Cover 1917326 Part Description QTY Input Pinion Shaft & Gear Assembly Main Drive ShaftWheel SHAFT, Eccentric Shaft and Tiller Shaft Assemblies Bolo TINES, Wheels Thicker than standard tinesElectric Start Assembly 1918831001 Battery Bracket ROW Marker Attachment Bumper Attachment2322 Bumper ROW Marker Attachment & Bumper AttachmentRow Marker Attachment option Description QTYHILLER/FURROWER Attachment Page Engine Service and Repair Warranty ServiceReplacement Parts Owner Registration Card