Craftsman 917-299751 owner manual To Start Engine See Fig, Tilling Hints, Tine Shear Pins

Page 12

OPERATION

TO START ENGINE (See Fig, 13)

I zt "OFF"...........posltlon............when, o,,startingoo°,engine,n.o,!

*Make sure spark plug wire is propedy connected°

. Move shift lever indicator to "N" (neutral) position.

. Place throttte control in "FAST" position°

. Place choke control in "CHOKE" positionif the engine iscoidoAwarm engine may not require choking to start.

. Grasp starter handle with one hand and grasp the tiller with other hand. Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point).

. Pull rope with arapid, continuous, full arm stroke. Keep a firm gdPon starter handle and let rope rewind slowly. Do not let starter handle snap back against starter.

. When engine starts, slowly move choke control on engine halfway between 'CHOKE" and "RUN" posi-

tions and then to "RUN" position as engine warms up,

. Move throttle control to desired running position.

. Allow engine to warm up for a few minutes before engaging tines.

NOTE: If at a high attitude (above 3000 feet) or in cold temperatures (beIow 32°t=), the carburetor fuel mixture

may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR in the Service and Adjust- ments section of this manual

SPARK

 

 

 

PLUG

_-,_=_

_

CHOKE

RECOIL STARTER / _ _---_

HANDLE

FIG. 13

TILLING HINTS

...............................i

i

i,i, l/

i

H i,,,,

handling your tiller, start actual field

CAUTION:use with throUntilyou!e In slowareaccustomedposition (toldto- way between FAST" and "IDLE").

•Tilling is digging into, turning over, and breaking up

packed soil before planting_ Loose, unpacked soil helps root growth_ Best tilling depth is 4'to 6'. A tiller will also clear the soil of unwanted vegetation. The decomposition of this vegetable matter enriches the soil, Depending on the climate (rainfall and wind), it

may be advisable to till the soil atthe end of the growing season to further condition the soil.

•Soil cond itions are importantfor proper tilling. Tines wilt not readity penetrate dry, hard soil which may contrib- ute to excessive bounce and difficult handling of your tiller, Hard soil should be moistened before tilling; however, extremely wet soi! wilt "ball-up" or clump during tilling, Wait until the soil is less wet in order to achieve the best results. When tilling inthe fall, remove vines and long grass to prevent them from wrapping around the tine shaft and slowing your tilling operation.

•For easier handling of your tiller, leave about 8 inches of untilled soil between the first and second tilling passes. The third pass will be between the first and second (See Fig. 14).

°Do not lean on handle.. This takes weight off the wheels and reduces traction. To get through a really tough section of sod or hard ground, apply upward pressure on handle or lower the depth stake.

3

FIG. 14

TINE SHEAR PINS

The line assemblies on your tiller are secured to the line shaft with shear pins (See "TINE REPLACEMENT" in the

Service and Adjustments section of this manual).

If the tiller is unusually overloaded or jammed, the shear pins are designed to break before internal damage occurs to the transmission.

•If shear pin(s) break, replace only with those shown in the Repair Parts section of this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents CRRFrZMR# Rear Tine Tiller WTH Counter Rotating TinesMaintenance and Storage Operation TrainingPreparation Limited ONE Year Warranty on Craftsman Tiller Product SpecificationsMaintenance Agreement Customer ResponsibilitiesTable of CON Tiller Plug Muffler AIR Filter GAS can EngineTines Clevis PIN BeltContents of Hardware Pack Operators Position See FigTo Assemble Your Tiller YOU will Need Handle LocksInstall Handle See Figs , 4, Unpacking Carton See FigMove Assembly Connect Shift ROD See FigRemove Tiller from Crate Insert Cable Clip See FigMeets Ansi Safety Requirements Safety DecalDeca! shown below is located on the handle of your tiller HOW to USE Your Tiller OperationDepth Stake See Fig EngineBefore Starting Engine Outer Side Shields See FigADD Gasoline TransportingTine Shear Pins To Start Engine See FigTilling Hints Handling your tiller, start actual fieldFigs CultivatingInner View of Tire Lubrication Chart Customer ResponsibilitiesBefore Each USE LubricationAIR Cleaner See Fig EngineCooling System See Fig Adjustments CleaningSpark Plug TransmissionErvnce and Adjustments Ground Drive Belt Adjustment SeeTo Remove Belt Guard See Fig To Replace Ground Drive Belt See FigsTine Replacement Gloves or other Protection when han Dling tinesSee Figs , 27 FIG+27To Adjust Throttle Control Cable See Fig Final SettingIdle RPM Adjustment ErviceStorage Engine OILTFtOUEILESHOOT NG Points Handles KEY Part Description MAINFRAME, Left Side KEY Part Description NO. no MAINFRAME, Right Side KEY Part Description NO. no KEY Part NO. no T6-18Tine Shield KEY Part Description NO, no Standard Hardware +PURCHASE LocallyPart Description Nut, Hex 3/8-24Washer, Lock 3/8 6555J Tine, Inner, R.H 6554J Tine, Inner, L.H 74610616 Bolt, Hex 3/8-24x6t5 614 392 191526 621 KEY Part DescriptionENGINE, Brggs & Stratton - Model Number 130202, Type no HOW to Order Repair Parts Model NumberEngine Model Number 130202, Type Number

917-299751 specifications

The Craftsman 917-299751 is a robust and efficient lawn tractor designed for homeowners seeking a reliable solution for their lawn care needs. This model features a powerful 19 horsepower Briggs & Stratton engine, providing ample power to handle a variety of terrain and mowing conditions. With a 42-inch cutting deck, the 917-299751 is well-suited for medium to large lawns, effectively reducing mowing time while ensuring a clean, even cut.

One of the standout features of the Craftsman 917-299751 is its Easy Start System. This technology allows for effortless starting, which is particularly convenient for users who may struggle with traditional pull-start engines. The engine is also equipped with a durable air filter that ensures optimal performance and longevity, minimizing maintenance needs.

The 917-299751 comes with a hydrostatic transmission, allowing for smooth and intuitive operation. This feature enables the operator to easily control the speed without needing to change gears, making it ideal for navigating obstacles like trees and flower beds. Additionally, the tight turning radius of the tractor enhances maneuverability, making it easier to reach difficult areas in the yard.

Comfort is another important aspect of the Craftsman 917-299751. The tractor is equipped with an adjustable high-back seat that provides added comfort during extended mowing sessions. The ergonomic layout of the controls ensures ease of access, allowing users to operate the mower with minimal effort.

For added versatility, the Craftsman 917-299751 supports various attachments, including mulchers and baggers. This compatibility allows users to customize their mowing experience based on their lawn care requirements. The tractor also features a washout port, enabling easy cleaning of the cutting deck after use, promoting maintenance and extending the life of the mower.

Built with durability in mind, the Craftsman 917-299751 is constructed with a robust frame and high-quality materials, ensuring it can withstand regular use over the years. The larger rear tires add stability and traction, allowing the mower to perform well even on uneven or hilly terrains.

In summary, the Craftsman 917-299751 combines power, comfort, and convenience, making it an excellent choice for homeowners looking to maintain their lawns efficiently. With its array of user-friendly features and durable construction, this lawn tractor is designed to meet the demands of any mowing job, while providing a satisfying user experience.
Top Page Image Contents