Craftsman 917.29332 owner manual Tiller, Fuel System, Engine OIL, Cylinders, Other

Page 19

Immediately prepare your tiller for storage at the end of the season or if the unit will

not be used for 30 days or more.

A_,CAUTION: Never store the tiller with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TILLER

Clean entire tiller (See =CLEANING" in the Customer Responsibilities section of this manual).

Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual).

Lubricate as shown in the Customer

Responsibilities section of this manual.

Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear.

Replace if necessary.

Touch up all rusted or chipped paint sur- faces; sand lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose, or tank during storage. also, experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can dam- age the fuel system of an engine while in storage.

Drain the fuel tank.

Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add sta- bilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine

at leP_t 10 minutes after adding stabilizer to allow the stabilizer to reach the carbure-

tor. Do not drain the gas tank and carbu- retor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See =ENGINE" in the

Customer Responsibilities section of this manual).

CYLINDER(S)

Remove spark plug,

Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder,

Pull starter handle slowly several times to distribute oil.

Replace with new spark plug,

OTHER

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

If possible, store your unit indoors and cover it to give protection from dust and d_rt.

C_ver your unit with a suitable protective

covP.r that does not retain moisture. Do

not'use plastic. Plastic cannot breathe which allows condensation to form and

will cause your unit to rust. IMPORTANT: Never cover tiller while

engine and exhaust areas are still warm.

19

Image 19
Contents Craftsman Preparation SEARS, Roebuckand CO., D/817WA, Hoffman ESTATES, IL TrainingOperation Maintenance and StorageCustomer Responsibilities Maintenance AgreementProduct Specifications RJ19LMLeft Right Tools Required for AssemblyOperators Position FrontViewed from R,H. Side of Tiller Install HandleHandle Height Connect Shift RODRemove Tiller from Crate Check Tire PressureKnow Your Tiller Meets Ansi Safety RequirementsEngine HOW USE Your TillerStopping Tines DriveTo Transport TurningCultivating Outer Side ShieldsTilling Hints To Start Engine0101010 0101010 0101010 Tine Shear PinsLubrication Chart To Change Engine OIL To Service PRE-CLEANERTo Service Cartridge Engine LubricationSpark Plug To Adjust Handle HeightCleaning MufflerTo Replace Ground Drive Belt Tire CareTo Remove Wheel To Remove Belt GuardTine Replacement To Adjus T Carburetor EngineCylinders TillerFuel System Engine OILCause ProblemCorrection Problem Cause KEY Part Description HandlesKEY Part MAINFRAME, Left SideDescription KEY Part Description MAINFRAME, Right SideStandardhardware - Purchaselocally KEY Part NO. NO. Description TransmissionTineshield Tine Assembly Decals Label KIT Ownersmanual ENGINE, Briggs & Stratton - Model Number 121432, Type no -E1 55A +++t Gasket SET Carburetor Gasietset Carburetor KIT 11098A 493280 Screws Idle Speed 690960 Screw, Blower Housing 305B 692557 Sears