Operating Instructions

BEFORE START UP

Follow the steps listed below before starting generator.

1.Check engine oil. Refer to the Engine Operator's Manual for correct grade and quantity of oil.

This generator has been shipped from the factory without oil in the crankcase. Operating the unit without oil can ruin the engine.

2.Check fuel level, fill as required. Make sure generator is turned off and has been allowed time to cool down.

3.Make sure generator is grounded.

4.All electrical loads should be disconnected.

IMPORTANT: Unit is equipped with a low oil shutdown system that will stop the engine should the crankcase oil level fall be- low the safe operating level. If generator shuts off and the oil level is according to specifications, check to see if generator is sitting level. Place on an even surface to correct this.

START UP-(Recoil start)

Do not operate generator indoors-exhaust fumes contain car- bon monoxide, an odorless and deadly gas.

1.Open the fuel shut-off valves. It is located in the fuel line. 2.Position ON\OFF\START switch on the control panel to

the "ON" position.

3.Move the choke control to "CHOKE" position. A cold engine may require to be choked longer than a warm engine.

4.Grasp handle on rope starter and pull slowly until resist- ance is felt. Then pull cord rapidly to overcome compression, prevent kickback, and start engine. Repeat if necessary.

NOTE: IF ENGINE OIL LEVEL IS TOO LOW, ENGINE WILL NOT START. CHECK OIL LEVEL AND ADD IF NECESSARY.

5.Open the choke gradually after engine starts. The engine should come up to full operating speed quickly. Do not allow choke to remain on after the engine has run for a short time. Avoid over-choking.

6.Allow generator to run at no load for 5 minutes upon each initial start-up to allow engine and generator to stabilize.

START UP-(Electric start)

1.Repeat steps 1, 2, and 3 listed above in recoil start procedures.

2.Push ON\OFF\START switch on control panel to the "START" position to start engine. Hold in "START" position no longer than 15 seconds per minute when trying to start engine. Extended cranking can damage the starter motor.

3.Repeat steps 5 and 6 listed above.

STOPPING ENGINE

1.Disconnect all electrical loads.

2.Turn on\off switch to "OFF" position.

3.Close both fuel shut-off valves.

STORING GENERATOR

When this generator is going to be stored for more than one month. Follow these instructions.

1.Fill engine oil to upper level. 2.Remove remaining fuel from fuel tank.

3.Start engine and allow it to run until all fuel in lines and carburetor has been used up and the engine stops.

4.Remove the spark plug and pour approximately one tea- spoon of engine oil into the cylinder. Pull starter rope slowly to distribute oil. Replace spark plug.

5.Store in a clean dry area.

MAINTENANCE SCHEDULE

	EVERY 5 HOURS	25 HOURS OR	50 HOURS OR	100 HOURS OR
MAINTENANCE OPERATION	OR DAILY	EVERY SEASON	EVERY SEASON	EVERY SEASON

Check Oil Level	X

Change Oil *			X
Change Oil *			NOTE 1
Change Air Filter		X
Change Air Filter		NOTE 2
Change Fuel Filter			X
Replace or Clean Spark Plug				X
Clean exterior of generator				X
				X
				NOTE 3

*Change oil after first 5 hours then after every 50 hours.

Note 1: Change oil every 25 hours when operating under heavy load or in high temperatures.

Note 2: Clean more often under dusty conditions.

Note 3: Clean exterior with cloth or brush. Do not use high pressure spray to clean generator or engine.

MGP-4600 specifications

DeVillbiss Air Power Company is renowned for its innovative and reliable air-powered tools, and one of its standout products is the MGP-4600. This versatile air compressor is engineered to meet the demands of professionals and DIY enthusiasts alike, offering a wide range of features that enhance performance and usability.

The MGP-4600 boasts a powerful motor that delivers robust air pressure, making it suitable for a variety of applications, including spray painting, pneumatic tool operation, and inflation tasks. With a maximum pressure of 125 PSI, it provides ample power for even the most demanding jobs. The compressor is designed to be user-friendly, featuring an easy-to-read pressure gauge that allows users to monitor performance at a glance.

One of the key technologies employed in the MGP-4600 is its oil-free pump system. This design not only reduces maintenance needs but also eliminates the risk of oil contamination, ensuring clean air output for painting and other sensitive operations. The pump is durable and efficient, offering a longer lifespan and consistent performance under heavy use.

Portability is another hallmark of the MGP-4600. Weighing in at a manageable size, it features a compact design, making it easy to transport and store. The ergonomic handle and rubberized wheels further enhance mobility, allowing users to navigate various work environments with ease.

Additionally, the MGP-4600 incorporates advanced safety features, including a thermal overload protection system that prevents overheating, safeguarding both the unit and the user. This ensures that the compressor operates within safe temperature limits, promoting durability and reliability over time.

Noise reduction is also a significant characteristic of the MGP-4600. Its design minimizes operational noise, making it suitable for use in residential areas or indoor environments where sound levels must be kept in check.

The MGP-4600 air compressor is compatible with a range of accessories, facilitating its use with various tools and attachments. This adaptability makes it a valuable addition to any workshop or job site, ensuring it meets the diverse needs of its users.

In summary, the DeVillbiss Air Power Company MGP-4600 stands out with its powerful performance, user-friendly features, and innovative technologies. It is a reliable choice for anyone seeking an efficient, portable, and versatile air compressor, making it an essential tool for both professionals and home users alike.