Poulan 437126, 96198003303 owner manual Auger Housing, Scraper BAR, Auger Bearing, Bearing Plug

Page 24

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303)

AUGER HOUSING / IMPELLER ASSEMBLY

1

 

 

KEY

PART

DESCRIPTION

 

3 (5x)

NO.

NO.

 

1

404929X428

AUGER HOUSING 27

 

4 (5x)

 

2

404932X431

SCRAPER BAR

2

 

 

3

72270505

CARRIAGE BOLT 5/16−18 X .625

 

 

4

155377

NUT 5/16−18

 

01.07.002-A

 

 

 

2

3

 

1

1

2

 

 

KEY

PART

DESCRIPTION

 

 

NO.

NO.

 

 

1

420478

AUGER BEARING

3

 

2

411939

BEARING PLUG

 

01.07.024-B

3

179582

SCREW 5/16−18 X 1.00

 

 

 

 

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHDeflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Handle Pivot Support WeldmentSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP1150E27 Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft SprocketENGINE, B&S Frame436146X428 Engine Mount PlateImpeller Belt Traction BeltIdler ARM Bracket Idler Pulley428684 Wheel Assembly LH Cable Bracket LHCable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 19307101.14.012-A Shifter ROD TOP Shifter ROD Bottom181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Limited Warranty
Top Page Image Contents