MTD E762F manual Maintenance and Storage, Safety labels found on your snow thrower

Page 4

If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble.

Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections. Never place your hand in the discharge or collector openings. Use a stick or wooden broom handle to unclog the discharge opening.

Take all possible precautions when leaving the unit unattended. Disengage the collector/impeller, shift into neutral, stop the engine, and remove the key.

When cleaning, repairing, or inspecting, make certain collector/impeller and all moving parts have stopped. Disconnect spark plug wire and keep away from plug to prevent accidental starting.

Do not run engine indoors, except when starting engine and transporting snow thrower in or out of building. Open doors. Exhaust fumes are dangerous.

Do not clear snow across the face of slopes. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes.

Never operate snow thrower without guards, plates, or other safety protection devices in place.

Never operate snow thrower near glass enclosure, automobiles, window wells, drop off, etc., without proper adjustments of snow thrower discharge angle. Keep children and pets away.

Do not overload machine capacity by attempting to clear snow at too fast a rate.

Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

Never direct discharge at bystanders or allow anyone in front of unit.

Disengage power to collector/impeller when transporting or not in use.

Use only attachments and accessories approved by the manufacturer of snow thrower (such as wheel weights, counter weights, cabs, etc.).

Never operate the snow thrower without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.

Muffler and engine become hot and can cause a burn. Do not touch.

4.MAINTENANCE AND STORAGE

Check shear bolts, engine mounting bolts, etc., at frequent intervals for proper tightness to be sure equipment is in safe working condition.

Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow engine to cool before storing in any enclosure.

Always refer to operator's manual instructions for important details if snow thrower is to be stored for an extended period.

Run machine a few minutes after throwing snow to prevent freeze up of collector/impeller.

Check clutch controls periodically to verify they engage and disengage properly and readjust if necessary. Refer to operator's manual for adjustment instructions.

WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

.AWAYCLOTHINGAND FEET HANDS, KEEP

-AUGER ROTATING FROM INJURY AVOID

DANGER

Safety labels found on your snow thrower.

WARNING

1.STOP ENGINE BEFORE REMOVING DEBRIS AND SERVICING UNIT

2.KEEP CLEAR OF IMPELLER WHILE ENGINE IS RUNNING

3.NEVER DIRECT DISCHARGE AT BYSTANDERS OR WINDOWS OR ALLOW ANYONE IN FRONT OF UNIT

4.THOROUGHLY INSPECT THE AREA WHERE THE EQUIPMENT IS TO BE

USED AND REMOVE ALL DOOR

MATS, SLEDS, BOARDS, WIRES AND

OTHER FOREIGN OBJECTS

5.REFER TO OWNERS MANUAL FOR FULL INSTRUCTIONS

3396MW

4

Image 4
Contents Important Read Safety Rules and Instructions Carefully MTD Products INC. P.O. BOX 368022 CLEVELAND, OhioCalling Customer Support Finding Your Model Number4683 Important Safe Operation Practices TrainingPreparation OperationMaintenance and Storage Safety labels found on your snow throwerContents of Hardware Pack Unpacking Assembly InstructionsHardware a Triangle Metal Tab Auger Control Group Fitting Hex Nut Attaching the Chute Assembly Attaching the Chute CrankHardware C Hardware DLamp Wiring Attaching the Track ControlsAttaching the Clutch Cables Attaching the Shift RODFinal Adjustments Skid Shoe AdjustmentTraction Drive Shift LeverControls Auger Drive ClutchTraction Drive Clutch Left and Right Track ControlsOperation GAS and OIL FILL-UPTo Start Engine To Stop EngineAdjustments Lubrication Maintenance Gear CaseChute Crank Auger BeltsDrive Belt Changing the Friction Wheel RubberOFF-SEASON Storage Trouble Shooting Guide Trouble Possible Causes Corrective ActionModel E762F Gearbox Assembly Parts ListModel E762F Blower Housing Part Description14 12 Handle Assembly Description3630 Frame Assembly 1713 Track Assembly Model E762F Engine and V-Belts Page MANUFACTURER’S Limited Warranty for