Poulan 96198002702, 435999 owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 21)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

17

Fig. 21

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See Figs a and 8BKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Auger Assembly LH Auger HousingAuger Assembly RH KEY Part DescriptionExploded 178675X431 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyBearing Plug Auger BearingSkid Plate LH Skid Plate RHChute Snow Shield 419822X431 Shield Retainer Strap Knob BlackPOP Rivet Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketHandle Grip 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHWasher Lower HandleRetainer SpacerKnob RED Handle KnobTraction ROD Impeller RODShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightSprocket Axle ShaftExploded Drive Plate Assembly Speed Selector AssemblyWheel HUB END PlateFrame Complete LCT Engine427963X428 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler Pulley432333X421 Wheel Assembly LH432334X421 Cable Bracket LHWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide422663 Safety Ignition KEYDECAL, DANGER, Deflector DECAL, DangerDECAL, Instruction DECAL, Speed ControlLimited Warranty

435999, 96198002702 specifications

The Poulan 96198002702,435999 is a high-performance chainsaw designed for both professional use and demanding residential applications. This powerful tool is engineered to deliver exceptional efficiency and reliability, making it a preferable choice for users seeking durability and cutting precision.

One of its main features is the robust engine. The Poulan chainsaw is equipped with a potent two-cycle engine that provides ample power for cutting through thick limbs and logs. The engine's design ensures quick start-up capabilities, which is crucial for maintaining productivity on the job site or during weekend projects.

The chainsaw incorporates a powerful 18-inch bar and chain, optimized for both speed and cutting efficiency. This length allows for a greater cutting capacity, making it suitable for a variety of tasks, from pruning small branches to felling larger trees. The chain itself is designed for optimal cutting performance, reducing kickback and ensuring smooth, clean cuts.

Another noteworthy characteristic is the chainsaw's lightweight construction. Weighing significantly less than many competitors in its class, the Poulan 96198002702,435999 is designed for easy handling. This feature reduces user fatigue during extended use, allowing for longer work periods without discomfort.

The chainsaw also boasts user-friendly technology. The automatic oiler ensures that the bar and chain remain lubricated during operation, thereby extending the life of the chain and providing consistent performance. The tool-free chain tensioning system allows users to quickly and easily adjust the chain to maintain optimal tension without the need for additional tools, ensuring safety and efficiency.

Additionally, the design of the Poulan chainsaw includes anti-vibration technology, which plays a crucial role in reducing user fatigue and increasing comfort. This feature lowers the amount of vibration transmitted to the user’s hands, enabling them to work longer without discomfort.

Safety is also a priority in the design of the Poulan 96198002702,435999. The chainsaw is equipped with features such as a chain brake to prevent accidental cuts and enhance user safety. Furthermore, the ergonomic handle provides a secure grip, allowing users to maintain control even in challenging conditions.

In summary, the Poulan 96198002702,435999 combines power, efficiency, and user-focused features to create a reliable chainsaw suitable for a broad range of applications. Whether for professional forestry work or home landscaping tasks, this chainsaw is designed to meet the demands of any cutting job while ensuring user safety and comfort.
Top Page Image Contents