Poulan 96198002702, 435999 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See Figs a and 8BIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting KEY Part Description Auger HousingAuger Assembly LH Auger Assembly RHExploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool BearingSkid Plate RH Auger BearingBearing Plug Skid Plate LHPOP Rivet Knob BlackChute Snow Shield 419822X431 Shield Retainer Strap Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHHandle Grip WasherHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelSprocket Axle ShaftExploded END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUBEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM BracketCable Bracket LH Wheel Assembly LH432333X421 432334X421Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe422663 Safety Ignition KEYDECAL, Speed Control DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty

435999, 96198002702 specifications

The Poulan 96198002702,435999 is a high-performance chainsaw designed for both professional use and demanding residential applications. This powerful tool is engineered to deliver exceptional efficiency and reliability, making it a preferable choice for users seeking durability and cutting precision.

One of its main features is the robust engine. The Poulan chainsaw is equipped with a potent two-cycle engine that provides ample power for cutting through thick limbs and logs. The engine's design ensures quick start-up capabilities, which is crucial for maintaining productivity on the job site or during weekend projects.

The chainsaw incorporates a powerful 18-inch bar and chain, optimized for both speed and cutting efficiency. This length allows for a greater cutting capacity, making it suitable for a variety of tasks, from pruning small branches to felling larger trees. The chain itself is designed for optimal cutting performance, reducing kickback and ensuring smooth, clean cuts.

Another noteworthy characteristic is the chainsaw's lightweight construction. Weighing significantly less than many competitors in its class, the Poulan 96198002702,435999 is designed for easy handling. This feature reduces user fatigue during extended use, allowing for longer work periods without discomfort.

The chainsaw also boasts user-friendly technology. The automatic oiler ensures that the bar and chain remain lubricated during operation, thereby extending the life of the chain and providing consistent performance. The tool-free chain tensioning system allows users to quickly and easily adjust the chain to maintain optimal tension without the need for additional tools, ensuring safety and efficiency.

Additionally, the design of the Poulan chainsaw includes anti-vibration technology, which plays a crucial role in reducing user fatigue and increasing comfort. This feature lowers the amount of vibration transmitted to the user’s hands, enabling them to work longer without discomfort.

Safety is also a priority in the design of the Poulan 96198002702,435999. The chainsaw is equipped with features such as a chain brake to prevent accidental cuts and enhance user safety. Furthermore, the ergonomic handle provides a secure grip, allowing users to maintain control even in challenging conditions.

In summary, the Poulan 96198002702,435999 combines power, efficiency, and user-focused features to create a reliable chainsaw suitable for a broad range of applications. Whether for professional forestry work or home landscaping tasks, this chainsaw is designed to meet the demands of any cutting job while ensuring user safety and comfort.
Top Page Image Contents