Poulan 435560, 96194000901 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USESnow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting KEY Part Description Exploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool BearingBearing Plug Skid Plate LHSkid Plate RH Auger BearingDeflector Spring Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldInterlock CAM Loop Handle LHLoop Handle RH Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPConsole Panel Wire HarnessLower Handle Pivot Support WeldmentSprocket Axle ShaftExploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM BracketClutch Slide CoverWheel Driver Retainer Ring Wheel LobeCable Bracket LH Wheel Assembly LHCable Bracket RH 422663 Safety Ignition KEYDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorHOP Limited Warranty

96194000901, 961940009, 435560 specifications

The Poulan 435560 (model numbers 961940009 and 96194000901) is a powerful chainsaw designed to meet the demands of both homeowners and professional users alike. This chainsaw combines robust performance with innovative technology, making it a versatile tool for various cutting tasks.

One of the primary features of the Poulan 435560 is its powerful 40cc, 2-cycle engine. This engine delivers impressive performance while offering a good balance between power and fuel efficiency. Users benefit from the chainsaw’s ability to tackle tough jobs such as falling trees, cutting firewood, or clearing brush, without sacrificing ease of use. The chainsaw is equipped with an automatic oiler, which ensures that the bar and chain remain well-lubricated during operation, extending the lifespan of these critical components and ensuring smooth cutting performance.

The Poulan 435560 also boasts a lightweight design, making it easy to maneuver and transport. Weighing in at approximately 10 pounds, the chainsaw minimizes user fatigue, allowing for longer periods of use without discomfort. Additionally, the chainsaw features an ergonomic handle design that provides a comfortable grip, enhancing user control and stability during operation.

Safety is a key consideration in the design of the Poulan 435560. It comes equipped with a chain brake that quickly stops the chain in case of kickback, reducing the risk of accidents. The chainsaw also includes a protective chain guard and a throttle lockout feature to further enhance user safety.

Another highlight of the Poulan 435560 is its ease of maintenance. The tool-less chain tensioning system allows for quick adjustments to the chain without the need for additional tools, ensuring that users can keep their chainsaw in optimal condition with minimal hassle.

Overall, the Poulan 435560 (961940009, 96194000901) is a feature-rich chainsaw that blends power, usability, and safety. Its advanced technologies, lightweight construction, and user-friendly features make it an excellent choice for anyone looking to invest in a reliable cutting tool. Whether you are a weekend warrior or a seasoned professional, the Poulan 435560 is designed to meet your needs and exceed your expectations.
Top Page Image Contents