Poulan 96194000901, 435560 owner manual Troubleshooting

Page 20

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

 

(or ON/OFF switch is OFF).

 

(or ON/OFF switch to ON position).

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service center/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service center/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service center/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationEngine CleaningSnow Thrower Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting KEY Part Description Exploded Gearbox Assembly 178675X431 Corner Bracket Clean OUT ToolBearing Impeller PulleySkid Plate LH Skid Plate RHAuger Bearing Bearing PlugKnob Black POP RivetChute Snow Shield 419822X431 Shield Retainer Strap Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHInterlock Spring Interlock CAMSpacer Knob REDHandle Knob Washer 3/8Impeller ROD Traction RODShifter ROD TOP Shifter ROD BottomWire Harness Lower HandlePivot Support Weldment Console PanelAxle Shaft SprocketExploded Assembly Drive Plate AssemblySpeed Selector Rubber RingComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyCover Wheel Driver Retainer RingWheel Lobe Clutch SlideCable Bracket RH Wheel Assembly LHCable Bracket LH Safety Ignition KEY 422663181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty HOP

96194000901, 961940009, 435560 specifications

The Poulan 435560 (model numbers 961940009 and 96194000901) is a powerful chainsaw designed to meet the demands of both homeowners and professional users alike. This chainsaw combines robust performance with innovative technology, making it a versatile tool for various cutting tasks.

One of the primary features of the Poulan 435560 is its powerful 40cc, 2-cycle engine. This engine delivers impressive performance while offering a good balance between power and fuel efficiency. Users benefit from the chainsaw’s ability to tackle tough jobs such as falling trees, cutting firewood, or clearing brush, without sacrificing ease of use. The chainsaw is equipped with an automatic oiler, which ensures that the bar and chain remain well-lubricated during operation, extending the lifespan of these critical components and ensuring smooth cutting performance.

The Poulan 435560 also boasts a lightweight design, making it easy to maneuver and transport. Weighing in at approximately 10 pounds, the chainsaw minimizes user fatigue, allowing for longer periods of use without discomfort. Additionally, the chainsaw features an ergonomic handle design that provides a comfortable grip, enhancing user control and stability during operation.

Safety is a key consideration in the design of the Poulan 435560. It comes equipped with a chain brake that quickly stops the chain in case of kickback, reducing the risk of accidents. The chainsaw also includes a protective chain guard and a throttle lockout feature to further enhance user safety.

Another highlight of the Poulan 435560 is its ease of maintenance. The tool-less chain tensioning system allows for quick adjustments to the chain without the need for additional tools, ensuring that users can keep their chainsaw in optimal condition with minimal hassle.

Overall, the Poulan 435560 (961940009, 96194000901) is a feature-rich chainsaw that blends power, usability, and safety. Its advanced technologies, lightweight construction, and user-friendly features make it an excellent choice for anyone looking to invest in a reliable cutting tool. Whether you are a weekend warrior or a seasoned professional, the Poulan 435560 is designed to meet your needs and exceed your expectations.
Top Page Image Contents