Poulan 96194000901 Assembly / PRE-OPERATION, Remove Snow Thrower from Carton, Unfold Upper Handle

Page 5

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD

 

RETAINER

 

SPRING

SPEED

SPEED

CONTROL

CONTROL

BRACKET

LEVER

FIG. 2

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Exploded 178675X431 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleySkid Plate RH Skid Plate LHAuger Bearing Bearing PlugPOP Rivet Knob BlackChute Snow Shield 419822X431 Shield Retainer Strap Deflector SpringCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LHInterlock Spring Interlock CAMKnob RED SpacerHandle Knob Washer 3/8Traction ROD Impeller RODShifter ROD TOP Shifter ROD BottomLower Handle Wire HarnessPivot Support Weldment Console PanelSprocket Axle ShaftExploded Drive Plate Assembly AssemblySpeed Selector Rubber RingFrame Complete LCT Engine427963X428 Engine Mounting PlateTraction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Driver Retainer Ring CoverWheel Lobe Clutch SlideCable Bracket RH Wheel Assembly LHCable Bracket LH 422663 Safety Ignition KEYDECAL, Danger 181037DECAL, DANGER, Deflector DECAL, InstructionHOP Limited Warranty

96194000901, 961940009, 435560 specifications

The Poulan 435560 (model numbers 961940009 and 96194000901) is a powerful chainsaw designed to meet the demands of both homeowners and professional users alike. This chainsaw combines robust performance with innovative technology, making it a versatile tool for various cutting tasks.

One of the primary features of the Poulan 435560 is its powerful 40cc, 2-cycle engine. This engine delivers impressive performance while offering a good balance between power and fuel efficiency. Users benefit from the chainsaw’s ability to tackle tough jobs such as falling trees, cutting firewood, or clearing brush, without sacrificing ease of use. The chainsaw is equipped with an automatic oiler, which ensures that the bar and chain remain well-lubricated during operation, extending the lifespan of these critical components and ensuring smooth cutting performance.

The Poulan 435560 also boasts a lightweight design, making it easy to maneuver and transport. Weighing in at approximately 10 pounds, the chainsaw minimizes user fatigue, allowing for longer periods of use without discomfort. Additionally, the chainsaw features an ergonomic handle design that provides a comfortable grip, enhancing user control and stability during operation.

Safety is a key consideration in the design of the Poulan 435560. It comes equipped with a chain brake that quickly stops the chain in case of kickback, reducing the risk of accidents. The chainsaw also includes a protective chain guard and a throttle lockout feature to further enhance user safety.

Another highlight of the Poulan 435560 is its ease of maintenance. The tool-less chain tensioning system allows for quick adjustments to the chain without the need for additional tools, ensuring that users can keep their chainsaw in optimal condition with minimal hassle.

Overall, the Poulan 435560 (961940009, 96194000901) is a feature-rich chainsaw that blends power, usability, and safety. Its advanced technologies, lightweight construction, and user-friendly features make it an excellent choice for anyone looking to invest in a reliable cutting tool. Whether you are a weekend warrior or a seasoned professional, the Poulan 435560 is designed to meet your needs and exceed your expectations.
Top Page Image Contents