To Remove Wheels See Fig | Poulan 96192000301, 401214 instruction

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME	AUGER
ASSEMBLY	HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from ﬁre or ﬂame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and ﬂat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing

the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install ﬂat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

	BELT KEEPER
	TRACTION DRIVE BELT
	ENGINE	FLAT WASHER
	PULLEY	FLAT WASHER
	PULLEY
		LOCKWASHER
		BOLT
IDLER ARM			AUGER
SQUARE			BELT
HOLE
CLUTCHING
IDLER ARM
BRACKET
	AUGER PULLEY
		BOLT	LOCK
			WASHER
FRAME	AUGER
FRAME	HOUSING

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 22

401214, 96192000301 specifications

The Poulan 401214,96192000301 is a versatile and efficient chainsaw designed for both professional and home use. Known for its durability and reliability, this model is ideal for a variety of tasks ranging from light trimming to heavy-duty cutting, making it a popular choice among homeowners and landscapers.

One of the most notable features of the Poulan 401214 is its powerful engine. Equipped with a robust two-stroke engine, the chainsaw delivers impressive cutting performance while maintaining fuel efficiency. This not only allows for longer operational time between refueling but also reduces the overall environmental impact. The engine's low-emission design meets stringent EPA standards, making it an eco-friendly choice in the chainsaw market.

Another standout characteristic is its lightweight construction. Weighing in at just under 10 pounds, the Poulan 401214 is designed for ease of handling. The lightweight design helps reduce user fatigue, especially during extended use. This feature is particularly beneficial for homeowners who may find themselves in need of a reliable cutting tool for longer projects.

The chainsaw utilizes a 16-inch bar and chain, allowing it to tackle a wide range of cutting tasks effectively. The length of the bar strikes a balance between agility and cutting capability, making it suitable for pruning branches, felling small trees, and cutting firewood. The chain is designed for easy maintenance and offers tool-less tensioning, so users can quickly adjust the tension as needed without requiring additional tools.

In terms of safety features, the Poulan 401214 is equipped with a chain brake, which is an essential addition for reducing the risk of accidents during operation. The equipped anti-vibration technology significantly minimizes vibrations, providing a more comfortable user experience while enhancing control during use.

In summary, the Poulan 401214,96192000301 chainsaw stands out due to its powerful engine, lightweight design, and user-friendly features. Its combination of performance, safety, and maintenance ease makes it an ideal choice for anyone looking to invest in a high-quality chainsaw that meets a variety of cutting needs. Whether for professional landscaping or home gardening projects, this chainsaw is sure to deliver reliability and efficiency.