Poulan 96192000301, 401214 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place contain- ers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller

 

housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Image 2
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingWhen cleaning, repairing, or inspecting, make When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig Stopped. Disconnect the spark plug wireTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes Limited Warranty

401214, 96192000301 specifications

The Poulan 401214,96192000301 is a versatile and efficient chainsaw designed for both professional and home use. Known for its durability and reliability, this model is ideal for a variety of tasks ranging from light trimming to heavy-duty cutting, making it a popular choice among homeowners and landscapers.

One of the most notable features of the Poulan 401214 is its powerful engine. Equipped with a robust two-stroke engine, the chainsaw delivers impressive cutting performance while maintaining fuel efficiency. This not only allows for longer operational time between refueling but also reduces the overall environmental impact. The engine's low-emission design meets stringent EPA standards, making it an eco-friendly choice in the chainsaw market.

Another standout characteristic is its lightweight construction. Weighing in at just under 10 pounds, the Poulan 401214 is designed for ease of handling. The lightweight design helps reduce user fatigue, especially during extended use. This feature is particularly beneficial for homeowners who may find themselves in need of a reliable cutting tool for longer projects.

The chainsaw utilizes a 16-inch bar and chain, allowing it to tackle a wide range of cutting tasks effectively. The length of the bar strikes a balance between agility and cutting capability, making it suitable for pruning branches, felling small trees, and cutting firewood. The chain is designed for easy maintenance and offers tool-less tensioning, so users can quickly adjust the tension as needed without requiring additional tools.

In terms of safety features, the Poulan 401214 is equipped with a chain brake, which is an essential addition for reducing the risk of accidents during operation. The equipped anti-vibration technology significantly minimizes vibrations, providing a more comfortable user experience while enhancing control during use.

In summary, the Poulan 401214,96192000301 chainsaw stands out due to its powerful engine, lightweight design, and user-friendly features. Its combination of performance, safety, and maintenance ease makes it an ideal choice for anyone looking to invest in a high-quality chainsaw that meets a variety of cutting needs. Whether for professional landscaping or home gardening projects, this chainsaw is sure to deliver reliability and efficiency.