Poulan 422073, 96192002301 owner manual Before Starting the Engine, To Start Engine

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then mov- ing skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR (See Fig. 17)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

11

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Exploded KEY Part Description Auger 27 RH Auger HousingScraper BAR Auger 27 LHBearing Plug Auger BearingStrap Chute WeldmentDeflector Weldment Deflector SealPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot Bracket405784X479 Pivot Support Weldment Loop Handle LHLoop Handle RH Handle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number XT8527ES Drive Control ARM Speed Selector Assembly43 402689 Drive Plate Assembly END PlateClik PIN Axle ShaftRoll PIN 3/16 Sprocket417014X505 Engine Mount Plate KEY Part Description Engine Tecumseh Model LH318SA-156551HImpeller Belt Belt CoverTraction Belt 187865X428 Wheel Assembly LH187833X428 35062 Safety Ignition KEYPart KEY Description DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty

422073, 96192002301 specifications

The Poulan 96192002301, 422073 is a highly versatile and powerful line trimmer designed to meet the demanding needs of both residential users and professional landscapers. With its robust construction and advanced features, this trimmer stands out in a competitive market, making it an excellent choice for trimming grass, weeds, and other vegetation with precision and ease.

One of the main features of the Poulan 96192002301, 422073 is its powerful engine, which provides ample power to tackle even the toughest tasks. The engine is designed for efficient performance, ensuring that users can complete their work quickly and effectively. The trimmer's lightweight design enhances maneuverability, allowing users to reach difficult areas without fatigue during prolonged use.

The Poulan trimmer incorporates a 2-cycle engine with an efficient fuel system, optimizing fuel consumption while minimizing emissions. This combination of power and efficiency makes it an environmentally friendly option, attractive to those who are conscious of their carbon footprint. The easy starting mechanism reduces the effort required to start the engine, enabling users to get to work without hassle.

In terms of cutting performance, the Poulan 96192002301, 422073 boasts a durable trimmer head equipped with a dual-line setup. This feature allows for a wider cutting swath, significantly reducing trimming time and improving efficiency. The trimmer head can be easily reloaded, ensuring that you spend more time working on your landscaping tasks and less time on maintenance.

Comfort is also a focal point in the design of this trimmer. It features an adjustable handle, which can be customized to fit users of different heights, promoting ergonomic use and reducing strain on the back and arms during operation. The lightweight body further contributes to ease of use, ensuring that operators can handle the trimmer for extended periods without discomfort.

Safety is paramount in any equipment, and the Poulan 96192002301, 422073 includes several safety features to protect users. The protective guard prevents debris from being thrown at the operator, while the throttle lock ensures that the engine runs smoothly and consistently.

Overall, the Poulan 96192002301, 422073 is a powerful and efficient line trimmer that combines advanced technology with user-friendly features. Whether you are a homeowner looking to keep your yard pristine or a professional landscaper maintaining commercial properties, this trimmer is designed to deliver reliable performance and exceptional results. Its blend of power, efficiency, and comfort makes it a standout choice for anyone in need of a reliable trimming solution.
Top Page Image Contents