Poulan 422073, 96192002301 owner manual Storage, Other

Page 17

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex-

17 haust area is still warm.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Exploded KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RHBearing Plug Auger BearingDeflector Weldment Chute WeldmentDeflector Seal StrapRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot405784X479 Pivot Support Weldment Loop Handle LHLoop Handle RH Retainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT8527ES Drive 43 402689 Drive Plate Assembly Speed Selector AssemblyEND Plate Control ARMRoll PIN 3/16 Axle ShaftSprocket Clik PIN417014X505 Engine Mount Plate KEY Part Description Engine Tecumseh Model LH318SA-156551HImpeller Belt Belt CoverTraction Belt 187865X428 Wheel Assembly LH187833X428 35062 Safety Ignition KEYPart KEY Description DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty

422073, 96192002301 specifications

The Poulan 96192002301, 422073 is a highly versatile and powerful line trimmer designed to meet the demanding needs of both residential users and professional landscapers. With its robust construction and advanced features, this trimmer stands out in a competitive market, making it an excellent choice for trimming grass, weeds, and other vegetation with precision and ease.

One of the main features of the Poulan 96192002301, 422073 is its powerful engine, which provides ample power to tackle even the toughest tasks. The engine is designed for efficient performance, ensuring that users can complete their work quickly and effectively. The trimmer's lightweight design enhances maneuverability, allowing users to reach difficult areas without fatigue during prolonged use.

The Poulan trimmer incorporates a 2-cycle engine with an efficient fuel system, optimizing fuel consumption while minimizing emissions. This combination of power and efficiency makes it an environmentally friendly option, attractive to those who are conscious of their carbon footprint. The easy starting mechanism reduces the effort required to start the engine, enabling users to get to work without hassle.

In terms of cutting performance, the Poulan 96192002301, 422073 boasts a durable trimmer head equipped with a dual-line setup. This feature allows for a wider cutting swath, significantly reducing trimming time and improving efficiency. The trimmer head can be easily reloaded, ensuring that you spend more time working on your landscaping tasks and less time on maintenance.

Comfort is also a focal point in the design of this trimmer. It features an adjustable handle, which can be customized to fit users of different heights, promoting ergonomic use and reducing strain on the back and arms during operation. The lightweight body further contributes to ease of use, ensuring that operators can handle the trimmer for extended periods without discomfort.

Safety is paramount in any equipment, and the Poulan 96192002301, 422073 includes several safety features to protect users. The protective guard prevents debris from being thrown at the operator, while the throttle lock ensures that the engine runs smoothly and consistently.

Overall, the Poulan 96192002301, 422073 is a powerful and efficient line trimmer that combines advanced technology with user-friendly features. Whether you are a homeowner looking to keep your yard pristine or a professional landscaper maintaining commercial properties, this trimmer is designed to deliver reliable performance and exceptional results. Its blend of power, efficiency, and comfort makes it a standout choice for anyone in need of a reliable trimming solution.
Top Page Image Contents