Poulan 96192001706, 421899 Snow Throwing Tips, Before Stopping, If Recoil Starter has Frozen

Page 12

OPERATION

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

6.Push the primer three (3) times.

7.Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

8.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

9.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Drive speed control lever used to select forward orHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Throw Snow See aTo Move Forward and Backward See Fig Before Starting the Engine To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Frame Auger Assembly Housing Handles Storage CarburetorEngine Speed Fuel SystemOther CylinderTroubleshooting Auger Housing KEY Part DescriptionScraper BAR Auger BearingAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHExploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Cable AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower - Model NO. PR8527ES Handles 01.08.004-B Repair Parts Snow Thrower - Model NO. PR8527ES Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive Speed Selector Assembly Drive Plate AssemblyShoulder Screw END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINENGINE, TEC FrameEngine Mount Plate Belt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower - Model NO. PR8527ES Wheels Wheel Assembly LH187833X421 187865X421Repair Parts Snow Thrower - Model NO. PR8527ES BAG of Parts Safety Ignition KEY35062 Repair Parts Snow Thrower - Model NO. PR8527ES Decals 181037DECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192001706, 421899 specifications

The Poulan 421899,96192001706 is a powerful and versatile outdoor tool designed to meet the needs of both homeowners and professionals. This particular product is known for its reliability and effectiveness in various landscaping tasks, including trimming, pruning, and even cutting through tougher branches.

One of the standout features of this model is its robust engine, which provides ample power to tackle challenging outdoor jobs. The engine is designed for optimal performance, ensuring that users can complete their tasks swiftly without sacrificing efficiency. The combination of a strong engine and lightweight design allows for prolonged use without significant fatigue, making it a favorite among those who require a dependable tool for extended periods.

In terms of technology, the Poulan 421899,96192001706 boasts advanced anti-vibration features that significantly enhance user comfort. This technology minimizes the amount of vibration felt during operation, allowing for smoother handling and greater precision when trimming or cutting. Users will appreciate how this feature reduces strain on their arms and hands, making it easier to handle the tool over long durations.

The design of the Poulan 421899,96192001706 also prioritizes user-friendliness. The easy-start system ensures that the tool can be fired up with minimal effort, which can be particularly beneficial for those who may struggle with traditional starting methods. Additionally, the ergonomic handle provides a comfortable grip, further enhancing control and maneuverability.

Durability is another key characteristic of this model. Built from high-quality materials, it is designed to withstand the rigors of outdoor use, whether in residential settings or more demanding commercial environments. The materials used in construction are resistant to wear and tear, ensuring that the tool lasts for many years with proper maintenance.

Another notable aspect of the Poulan 421899,96192001706 is its versatility. With compatible attachments and a range of performance options, it can easily adapt to various tasks. This multifunctional capability makes it an invaluable addition to any toolkit, whether for landscaping, gardening, or general outdoor maintenance.

In conclusion, the Poulan 421899,96192001706 is a well-rounded outdoor tool that combines power, advanced technology, and ease of use. Its robust engine, anti-vibration features, and ergonomic design make it a top choice for those looking for efficiency and comfort in their outdoor tasks. With its durability and versatility, it stands out in the market, proving itself to be a reliable partner for both amateur gardeners and professional landscapers alike.
Top Page Image Contents