Poulan 421899, 96192001706 owner manual Storage, Carburetor, Engine Speed, Fuel System, Engine OIL

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 21

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See a To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Frame Auger Assembly Housing Handles Carburetor StorageEngine Speed Fuel SystemCylinder OtherTroubleshooting KEY Part Description Auger HousingScraper BAR Auger BearingAuger 27 RH Auger 27 LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyDeflector Weldment Chute WeldmentDeflector Seal StrapCable Assembly LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower - Model NO. PR8527ES Handles 01.08.004-B Repair Parts Snow Thrower - Model NO. PR8527ES Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive Drive Plate Assembly Speed Selector AssemblyShoulder Screw END PlateRoll PIN 3/16 Axle ShaftSprocket Clik PINEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model NO. PR8527ES Wheels187833X421 187865X42135062 Repair Parts Snow Thrower - Model NO. PR8527ES BAG of PartsSafety Ignition KEY 181037 Repair Parts Snow Thrower - Model NO. PR8527ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192001706, 421899 specifications

The Poulan 421899,96192001706 is a powerful and versatile outdoor tool designed to meet the needs of both homeowners and professionals. This particular product is known for its reliability and effectiveness in various landscaping tasks, including trimming, pruning, and even cutting through tougher branches.

One of the standout features of this model is its robust engine, which provides ample power to tackle challenging outdoor jobs. The engine is designed for optimal performance, ensuring that users can complete their tasks swiftly without sacrificing efficiency. The combination of a strong engine and lightweight design allows for prolonged use without significant fatigue, making it a favorite among those who require a dependable tool for extended periods.

In terms of technology, the Poulan 421899,96192001706 boasts advanced anti-vibration features that significantly enhance user comfort. This technology minimizes the amount of vibration felt during operation, allowing for smoother handling and greater precision when trimming or cutting. Users will appreciate how this feature reduces strain on their arms and hands, making it easier to handle the tool over long durations.

The design of the Poulan 421899,96192001706 also prioritizes user-friendliness. The easy-start system ensures that the tool can be fired up with minimal effort, which can be particularly beneficial for those who may struggle with traditional starting methods. Additionally, the ergonomic handle provides a comfortable grip, further enhancing control and maneuverability.

Durability is another key characteristic of this model. Built from high-quality materials, it is designed to withstand the rigors of outdoor use, whether in residential settings or more demanding commercial environments. The materials used in construction are resistant to wear and tear, ensuring that the tool lasts for many years with proper maintenance.

Another notable aspect of the Poulan 421899,96192001706 is its versatility. With compatible attachments and a range of performance options, it can easily adapt to various tasks. This multifunctional capability makes it an invaluable addition to any toolkit, whether for landscaping, gardening, or general outdoor maintenance.

In conclusion, the Poulan 421899,96192001706 is a well-rounded outdoor tool that combines power, advanced technology, and ease of use. Its robust engine, anti-vibration features, and ergonomic design make it a top choice for those looking for efficiency and comfort in their outdoor tasks. With its durability and versatility, it stands out in the market, proving itself to be a reliable partner for both amateur gardeners and professional landscapers alike.
Top Page Image Contents