Poulan 96192004601, 438364 owner manual KEY Part Description

Page 23

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004601)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X431 IMPELLER

2427148 GEARBOX ASSEMBLY

3	188909	BEARING
4	427146	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X431 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4-20
10	74780426	SCREW 1/4-20 X .625
11	427942	NUT 5/16-18
12	163183	SCREW 5/16-18 X .625
13	427145	IMPELLER HUB
14	427154	IMPELLER SLEEVE
15	73900600	NUT 3/8-16
16	180355	CARRIAGE BOLT
17	194189	SCREW 13-16 X .625
18	407760	PLUG
19	427302	GEARBOX COVER RH
20	427345	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	427147	IMPELLER SHAFT
30	184205	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O-RING
35	407767	SCREW 5/16-18 X .750
36	427317	GEARBOX COVER LH
37	192090	SHEAR BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 23

Image 23

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHChute Snow Shield 419822X431 Shield Retainer Strap Deflector SealKnob Black POP RivetKEY Part Lower Handle Loop Handle LHLoop Handle RH 419797X431Handle Knob SpacerRetainer Knob REDCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Flood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PR8P27ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUBSprocket Axle ShaftEngine Mount Plate ENGINE, B&SFrame 436146X421428684 Clutch Slide CoverWheel Driver Wheel LobeCable Bracket LH Wheel Assembly LH432337X428 432338X428193071 Safety Ignition KEYKIT Harness Conn B&S Shifter ROD TOP Shifter ROD Bottom435840 DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty