Poulan 96192004601, 438364 Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
		BETWEEN
		HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

7

Image 7

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHChute Snow Shield 419822X431 Shield Retainer Strap Deflector SealKnob Black POP RivetKEY Part Lower Handle Loop Handle LHLoop Handle RH 419797X431Handle Knob SpacerRetainer Knob REDCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Flood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PR8P27ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUBSprocket Axle ShaftEngine Mount Plate ENGINE, B&SFrame 436146X421428684 Clutch Slide CoverWheel Driver Wheel LobeCable Bracket LH Wheel Assembly LH432337X428 432338X428193071 Safety Ignition KEY435840 Shifter ROD TOP Shifter ROD BottomKIT Harness Conn B&S DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty