Poulan 438364 Parts Packed Separately in Carton, Assembly / PRE-OPERATION, Tool BOX See Fig

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) MULTI-

WRENCH

(180684)

(1) POWER CORD

SAFTEY IGNITION KEY(S)

(198563)

(193071)

(1) AUGER CONTROL ROD

(1) DISCHARGE CHUTE

EXTRA SHEAR BOLTS AND NUTS

(2) SHOULDER

(2) LOCKNUTS

BOLT 1/4-20 x 1-3/4

1/4-20

(192090)

(73800400)

ROTATOR HEAD MOUNTING

(3) RETAINER SPRINGS (169675)

(1) WASHER 3/8

(1) LOCKNUT 3/8

(19131316)

(73800600)

CHUTE DEFLECTOR REMOTE CONTROL

(1) LOCKNUT

(1) CARRIAGE BOLT

(1) LOCKNUT

(1) SHOULDER

(1) SPRING

5/16-18

5/16-18 x 5/8

1/4-20

BOLT 1/4-20

(751153)

(72250505)

(191730)

(179829)

(184505)

(2)FLAT WASHERS

(2)CARRIAGE BOLTS 3/8-16 x 2.25

(2)HANDLE KNOBS

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

REMOVE SNOW THROWER FROM CARTON

 

A toolbox is provided on your snow thrower. The toolbox is

1. Remove all accessible loose parts and parts boxes

 

located on top of the belt cover. Store the extra shear bolts,

 

nuts and multi-wrench provided in parts bag in the toolbox.

from carton.

4

 

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHDeflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapKEY Part Loop Handle LH Loop Handle RH419797X431 Lower HandleSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PR8P27ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft SprocketENGINE, B&S Frame436146X421 Engine Mount Plate428684 Cover Wheel DriverWheel Lobe Clutch SlideWheel Assembly LH 432337X428432338X428 Cable Bracket LHSafety Ignition KEY 193071435840 Shifter ROD TOP Shifter ROD BottomKIT Harness Conn B&S DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty
Top Page Image Contents