Poulan 96192004600 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 19)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shear bolt and hex nut. Should a foreign ob- ject or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared.

To replace the capscrew/shear bolts:

16

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 19

TO REMOVE BELT COVER (See Fig. 20)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 20

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHDeflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketLoop Handle LH Loop Handle RH419797X431 Lower HandleSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PR8P27ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft SprocketENGINE, B&S Frame436146X421 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler Pulley428684 Wheel Assembly LH 432337X428432338X428 Cable Bracket LHCover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 193071DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty

PR8P27ES, 96192004600, 438361 specifications

The Poulan 438361, 96192004600, and PR8P27ES are notable offerings from Poulan Pro, a brand known for its innovation in outdoor power equipment. These tools are designed to cater to a variety of landscaping and maintenance tasks, making them essential for both residential users and professionals.

The Poulan 438361 is particularly recognized for its efficient performance. It features a robust 38cc two-stroke engine that delivers ample power for tasks such as trimming, edging, and light brush clearing. The combination of lightweight design and an ergonomic handle allows users to operate the equipment with minimal fatigue, even during extended periods. The advanced air filtration system helps prolong engine life by reducing the risk of clogging, ensuring that peak performance is maintained over time.

The 96192004600 offers a unique attachment system that enhances its versatility significantly. This multi-tool design allows users to customize their equipment by exchanging attachments for different tasks, such as pruning, blowing leaves, or tilling. This adaptability not only saves users from needing multiple machines but also provides a streamlined experience for homeowners and professionals alike. With easy-to-follow instructions and quick-change couplings, switching between attachments requires minimal effort.

The PR8P27ES model emphasizes user convenience with its push-start technology. This electric start feature eliminates the hassle of traditional pull-start mechanisms, offering an easier experience, especially for those less experienced in handling power tools. Its durable construction ensures long-lasting performance, while the low maintenance requirements mean that users can spend more time focused on their projects rather than on upkeep.

All three models benefit from Poulan Pro's commitment to safety and comfort. Features like anti-vibration technology in the handles and noise-reduction designs provide a more pleasant user experience. Additionally, the incorporation of safety switches and guards ensures that users can operate these machines with confidence.

In conclusion, the Poulan 438361, 96192004600, and PR8P27ES models embody a range of technologies and features that position them as top choices for outdoor power equipment. With their powerful engines, versatile attachment capabilities, and user-centric designs, these tools meet a variety of landscaping needs while ensuring reliability and ease of use. Whether for professional landscaping or home maintenance, these Poulan Pro models stand out as efficient and effective solutions.
Top Page Image Contents