Poulan 438361 To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 22

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 23)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 23

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing PlugSkid Plate LH Auger 27 LHAuger 27 RH Skid Plate RHPOP Rivet Deflector SealKnob Black Chute Snow Shield 419822X431 Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket419797X431 Loop Handle LHLoop Handle RH Lower HandleKnob RED SpacerRetainer Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Headlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number PR8P27ES Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END PlateAxle Shaft Sprocket436146X421 ENGINE, B&SFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley428684 432338X428 Wheel Assembly LH432337X428 Cable Bracket LHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 193071181037 DECAL, DangerDECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty

PR8P27ES, 96192004600, 438361 specifications

The Poulan 438361, 96192004600, and PR8P27ES are notable offerings from Poulan Pro, a brand known for its innovation in outdoor power equipment. These tools are designed to cater to a variety of landscaping and maintenance tasks, making them essential for both residential users and professionals.

The Poulan 438361 is particularly recognized for its efficient performance. It features a robust 38cc two-stroke engine that delivers ample power for tasks such as trimming, edging, and light brush clearing. The combination of lightweight design and an ergonomic handle allows users to operate the equipment with minimal fatigue, even during extended periods. The advanced air filtration system helps prolong engine life by reducing the risk of clogging, ensuring that peak performance is maintained over time.

The 96192004600 offers a unique attachment system that enhances its versatility significantly. This multi-tool design allows users to customize their equipment by exchanging attachments for different tasks, such as pruning, blowing leaves, or tilling. This adaptability not only saves users from needing multiple machines but also provides a streamlined experience for homeowners and professionals alike. With easy-to-follow instructions and quick-change couplings, switching between attachments requires minimal effort.

The PR8P27ES model emphasizes user convenience with its push-start technology. This electric start feature eliminates the hassle of traditional pull-start mechanisms, offering an easier experience, especially for those less experienced in handling power tools. Its durable construction ensures long-lasting performance, while the low maintenance requirements mean that users can spend more time focused on their projects rather than on upkeep.

All three models benefit from Poulan Pro's commitment to safety and comfort. Features like anti-vibration technology in the handles and noise-reduction designs provide a more pleasant user experience. Additionally, the incorporation of safety switches and guards ensures that users can operate these machines with confidence.

In conclusion, the Poulan 438361, 96192004600, and PR8P27ES models embody a range of technologies and features that position them as top choices for outdoor power equipment. With their powerful engines, versatile attachment capabilities, and user-centric designs, these tools meet a variety of landscaping needs while ensuring reliability and ease of use. Whether for professional landscaping or home maintenance, these Poulan Pro models stand out as efficient and effective solutions.
Top Page Image Contents