Poulan 438361, 96192004600, PR8P27ES owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and working.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

3.0 Quarts (2,84 Liters)

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 5W-30 or 10W-30

(API SG–SL):

Synthetic SAE 5W-30

 

 

Oil Capacity:

21 Ounces (0,62 Liters)

 

 

Spark Plug:

Champion RC12YC/491055

Gap:

0.030" (0,762 mm)

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

4-7

OPERATION

8-13

MAINTENANCE SCHEDULE

14

MAINTENANCE

14-15

SERVICE AND ADJUSTMENTS

16-18

STORAGE

19

TROUBLESHOOTING

20

REPAIR PARTS

22-41

WARRANTY

BACK COVER

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHChute Snow Shield 419822X431 Shield Retainer Strap Deflector SealKnob Black POP RivetRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle Loop Handle LHLoop Handle RH 419797X431Handle Knob SpacerRetainer Knob REDCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Flood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PR8P27ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUBSprocket Axle ShaftEngine Mounting Plate ENGINE, B&SFrame 436146X421Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket428684 Cable Bracket LH Wheel Assembly LH432337X428 432338X428Clutch Slide CoverWheel Driver Retainer Ring Wheel Lobe193071 Safety Ignition KEY181037 DECAL, DangerDECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty

PR8P27ES, 96192004600, 438361 specifications

The Poulan 438361, 96192004600, and PR8P27ES are notable offerings from Poulan Pro, a brand known for its innovation in outdoor power equipment. These tools are designed to cater to a variety of landscaping and maintenance tasks, making them essential for both residential users and professionals.

The Poulan 438361 is particularly recognized for its efficient performance. It features a robust 38cc two-stroke engine that delivers ample power for tasks such as trimming, edging, and light brush clearing. The combination of lightweight design and an ergonomic handle allows users to operate the equipment with minimal fatigue, even during extended periods. The advanced air filtration system helps prolong engine life by reducing the risk of clogging, ensuring that peak performance is maintained over time.

The 96192004600 offers a unique attachment system that enhances its versatility significantly. This multi-tool design allows users to customize their equipment by exchanging attachments for different tasks, such as pruning, blowing leaves, or tilling. This adaptability not only saves users from needing multiple machines but also provides a streamlined experience for homeowners and professionals alike. With easy-to-follow instructions and quick-change couplings, switching between attachments requires minimal effort.

The PR8P27ES model emphasizes user convenience with its push-start technology. This electric start feature eliminates the hassle of traditional pull-start mechanisms, offering an easier experience, especially for those less experienced in handling power tools. Its durable construction ensures long-lasting performance, while the low maintenance requirements mean that users can spend more time focused on their projects rather than on upkeep.

All three models benefit from Poulan Pro's commitment to safety and comfort. Features like anti-vibration technology in the handles and noise-reduction designs provide a more pleasant user experience. Additionally, the incorporation of safety switches and guards ensures that users can operate these machines with confidence.

In conclusion, the Poulan 438361, 96192004600, and PR8P27ES models embody a range of technologies and features that position them as top choices for outdoor power equipment. With their powerful engines, versatile attachment capabilities, and user-centric designs, these tools meet a variety of landscaping needs while ensuring reliability and ease of use. Whether for professional landscaping or home maintenance, these Poulan Pro models stand out as efficient and effective solutions.
Top Page Image Contents