Poulan 429890 Lower Tube, Pivot Support, Console Panel, Headlight Bezel, Flood Headlight, Bulb

Page 30

REPAIR PARTS HANDLES

01.05.004-C

SNOW THROWER - MODEL 961940009 (96194000901)

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	419797X479	LOWER TUBE
	2	418313X479	PIVOT SUPPORT
	3	428867	BOLT 5/16-18 X .750
2	4	17000616	SCREW 3/8-16 X 1.00

7	4

	3			5
	2
				KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
			1	1	429624	CONSOLE PANEL
	5	4	1	2	178668	HEADLIGHT BEZEL
6		4		3	180927	FLOOD HEADLIGHT
				3	180927	FLOOD HEADLIGHT
				4	184471	SHOULDER SCREW 10−24 X .625
				4	184471	SHOULDER SCREW 10−24 X .625
				5	175262	SCREW 10−24 X 1.25
		01.10.027-A		6	178770	WIRE HARNESS
		01.10.027-A		7	183784	BULB

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 30

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyAuger Bearing Bearing PlugChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketInterlock Spring Loop Handle LHLoop Handle RH Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomPivot Support Wire HarnessLower Tube Console PanelAxle Shaft SprocketExploded Speed Selector AssemblyDrive Plate Assembly Rubber RingFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 422663181037 DECAL, DangerDECAL, DANGER, Deflector Limited Warranty HOP

REPAIR PARTS HANDLES

SNOW THROWER - MODEL 961940009 (96194000901)

KEY

LOWER TUBE

PIVOT SUPPORT

KEY

CONSOLE PANEL

HEADLIGHT BEZEL

FLOOD HEADLIGHT

SHOULDER SCREW 10−24 X .625

01.10.027-A

WIRE HARNESS

BULB