Poulan 429890 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot

Page 26

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901) CONTROL PANEL / DISCHARGE CHUTE

2

2

*3

1

*7

KEY

PART

*6

 

 

 

DESCRIPTION

 

 

 

NO.

NO.

 

 

 

1

428272

LEVER/CABLE ROTATOR ASSEMBLY

 

 

 

2

17501010

SCREW 10-24 X .625

*4

 

 

*3

420678

ROTATOR HEAD

01.09.010-A

*5

*4

405932

ROTATOR PIVOT BRACKET

 

 

 

 

*5

420675

PULLEY PIVOT

 

 

 

*6

428273

CABLE ASSEMBLY ADJUSTABLE

 

 

 

*7

428310

CABLE ASSEMBLY HEAT SHIELD

 

 

 

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

2

101.15.009-A

KEY

PART

DESCRIPTION

NO.

NO.

1

421249

STEER CABLE

2

74041024

SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationEngine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyAuger Bearing Bearing PlugChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketInterlock Spring Loop Handle LHLoop Handle RH Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomPivot Support Wire HarnessLower Tube Console PanelAxle Shaft SprocketExploded Speed Selector AssemblyDrive Plate Assembly Rubber RingFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 422663DECAL, DANGER, Deflector 181037DECAL, Danger Limited Warranty HOP
Top Page Image Contents