Poulan 429890 owner manual 422663, Safety Ignition KEY

Page 38

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901) BAG OF PARTS

01.14.003-B

4	KEY	PART
			DESCRIPTION
6	NO.	NO.
5	1	198563	POWER CORD
8
	2	169675	RETAINER PIN
7

3180684X008 WRENCH

4184505 REMOTE SPRING

		5	179829	SHOULDER BOLT 1/4-20
	9 10	6	191730	LOCKNUT 1/4-20
	9 10	7	72250505	CARRIAGE BOLT 5/16-18 X 5/8
		8	751153	LOCKNUT 5/16-18
		9	73800600	LOCKNUT 3/8-16
		10	19131316	WASHER 3/8
		11	192090	SHEAR BOLT 1/4-20 X 1-13/16
		12	73800400	LOCKNUT 1/4-20
1	12
1
	11

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	422663	SAFETY IGNITION KEY

	1
	01.14.009-A
1	3	2

1	4
		2
	2.56	01.14.012-A
		01.14.012-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	180445	SHIFTER ROD TOP
2	187716	SHIFTER ROD BOTTOM
3	72270505	CARRIAGE BOLT 5/16-18 X .75
4	155377	NUT 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 38

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationEngine CleaningSnow Thrower Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part Description23 22 Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyAuger Bearing Bearing PlugChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketInterlock Spring Loop Handle LHLoop Handle RH Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomPivot Support Wire HarnessLower Tube Console PanelAxle Shaft SprocketExploded Speed Selector AssemblyDrive Plate Assembly Rubber RingFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideCable Bracket LH Cable Bracket RHSafety Ignition KEY 422663DECAL, DANGER, Deflector 181037DECAL, Danger Limited Warranty HOP

KEY

SHOULDER BOLT 1/4-20

WASHER 3/8

KEY

422663

SAFETY IGNITION KEY

01.14.009-A

KEY

SHIFTER ROD TOP

SHIFTER ROD BOTTOM