Poulan 438371, 96192004602 owner manual Auger Housing, Scraper BAR, Auger Bearing, Bearing Plug

Page 24

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PR8P27ES (96192004602)

AUGER HOUSING / IMPELLER ASSEMBLY

1

 

 

KEY

PART

DESCRIPTION

 

3 (5x)

NO.

NO.

 

1

404929X421

AUGER HOUSING 27

 

4 (5x)

 

2

404932X431

SCRAPER BAR

2

 

 

3

72270505

CARRIAGE BOLT 5/16−18 X .625

 

 

4

155377

NUT 5/16−18

 

01.07.002-A

 

 

 

2

3

 

1

1

2

 

 

KEY

PART

DESCRIPTION

 

 

NO.

NO.

 

 

1

420478

AUGER BEARING

3

 

2

411939

BEARING PLUG

 

01.07.024-B

3

179582

SCREW 5/16−18 X 1.00

 

 

 

 

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RHDeflector Seal Knob BlackPOP Rivet Chute Snow Shield 419822X431 Shield Retainer StrapKEY Part Loop Handle LH Loop Handle RH419797X431 Lower HandleSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PR8P27ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft SprocketENGINE, B&S Frame436146X421 Engine Mounting Plate428684 Cover Wheel DriverWheel Lobe Clutch SlideWheel Assembly LH Cable Bracket LHCable Bracket RH Safety Ignition KEY 193071181037 DECAL, DangerDECAL, DANGER, Deflector Service Notes Service Notes Service Notes Limited Warranty
Top Page Image Contents