Poulan 429264 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Pulley ENG Impeller

Page 36

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003301)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14	21
24				21
				20
11
14	21		20	19
13			20	18
13				18
12				17
12	14			16
		15		16
		15		6
				6
	7
10
				5
8				4
8				3
				3
				9

1

2

01.21.003-A

KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	408007	IMPELLER BELT	14	59289	WASHER
2	419744	TRACTION BELT	15	73930500	NUT 5/16-18
3	423723X479	IDLER ARM BRACKET	16	851084	SCREW 3/8-24 X 1.375
4	180523X479	IDLER PULLEY	17	400026	WASHER
5	426589	NUT 5/16-18	18	426491	PULLEY ENG IMPELLER
6	74780524	SCREW 5/16-18 X 1 .50	19	426490	PULLEY ENG TRACTION
7	423990	IDLER BRACKET	20	74610516	SCREW 5/16-18 X 1 .00
8	428867	SCREW 5/16-18 X .625	21	10040500	LOCKWASHER 5/16
9	424297	SHOULDER BOLT 5/16-18 X .500	22	155452	BELT GUIDE
10	427942	NUT 5/16-18 NYLOCK	23	11050500	LOCKWASHER 5/16
11	187786	TRACTION IDLER ARM	24	175331	IDLER BUSHING
12	180522	TRACTION PULLEY
13	74780520	SCREW 5/16-18 X 1 .00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 36

Image 36

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes 23 22 KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger 27 LH Auger 27 RHKnob Black POP RivetShoulder Screw Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP1150E27 Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END Plate01.03.002-A ENGINE, B&S Frame423185X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyCover Assembly Repair Parts Snow Thrower - Model Number PP1150E27 Wheels Cable Bracket LH Cable Bracket RHCover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 193071181037 DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty