Poulan 429264, 96198003301 owner manual Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATER		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATER HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

6

Image 6

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes 23 22 KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing PlugAuger 27 LH Auger 27 RHShoulder Screw Knob BlackPOP Rivet Deflector SpringCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Loop Handle LHLoop Handle RH Pivot SupportKnob RED SpacerRetainer Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Headlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number PP1150E27 Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END Plate01.03.002-A 423185X428 ENGINE, B&SFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyCover Assembly Repair Parts Snow Thrower - Model Number PP1150E27 Wheels Cable Bracket LH Cable Bracket RHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 193071DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, InstructionService Notes Service Notes Limited Warranty