Poulan 96192002800, 428510 Maintenance, General Recommendations, Before Each USE, Lubrication

Page 13

MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower.

At least once a season, check to see if you should make any of the adjustments described in the Service and Ad- justments section of this manual.

•At least once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRICATION CHART”).

➀SAE 30 Motor Oil

➁ See “ENGINE” in

Maintenance section

➂ General

Purpose

Grease

➀ Pivot points

➁ Engine

➂ Auger

oil

grease fittings

SNOW THROWER

Always observe the safety rules when performing any maintenance.

TIRES

•Maintain proper air pressure in both tires (14–17 P.S.I. / 19-24.5 N-m).

•Keep tires free of gasoline and oil, which can harm rubber.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting 12 16 23 22 KEY Part Description Auger Assembly LH Auger HousingAuger Assembly RH Scrapper BARBearing Plug Auger BearingDeflector Weldment Chute WeldmentDeflector Seal StrapCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadHandle Grip Panel Bracket LH Panel Bracket RHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobTraction ROD Impeller RODShifter ROD TOP Shifter ROD BottomConsole Panel 01.10.001-BRepair Parts Snow Thrower - Model Number PR6R24 Drive Drive Plate Assembly AssemblySpeed Selector Rubber RingRoll PIN 3/16 Axle ShaftSprocket Clik PINComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley187831X421 Wheel Assembly LH187866X421 422663 Safety Ignition KEYDECAL, DANGER, Deflector DECAL, DangerDECAL, Instruction DECAL, Auger Lever RTService Notes Service Notes Limited Warranty
Top Page Image Contents