Poulan PR6R24 To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 21

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

17

Image 17

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting 12 16 23 22 KEY Part Description Auger Assembly LH Auger HousingAuger Assembly RH Scrapper BARBearing Plug Auger BearingDeflector Weldment Chute WeldmentDeflector Seal StrapCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadHandle Grip Panel Bracket LH Panel Bracket RHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobTraction ROD Impeller RODShifter ROD TOP Shifter ROD BottomConsole Panel 01.10.001-BRepair Parts Snow Thrower - Model Number PR6R24 Drive Drive Plate Assembly AssemblySpeed Selector Rubber RingRoll PIN 3/16 Axle ShaftSprocket Clik PINComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley187866X421 Wheel Assembly LH187831X421 422663 Safety Ignition KEYDECAL, DANGER, Deflector DECAL, DangerDECAL, Instruction DECAL, Auger Lever RTService Notes Service Notes Limited Warranty