MTD E663G manual Lens Assembly / Lamp Housing

Page 25

Model 663

	Ref.	Part No.	Part Description
	No.

1.684-0008A Shift Arm Assembly

2.	684-0022	Chute Crank Ass’y
3.	715-0138	Rolled Pin
4.	710-0262	Carriage Bolt, 5/16-18 x 1.5
5.	710-0449	Carriage Bolt, 5/16-18 x 2.25
6.	710-0788	Self Tapping Screw, 1/4-20 x 1
7.	710-3008	Hex Cap Screw, 5/16-18 x .75
8.	710-3015	Hex Cap Screw, 1/4-20 x .75
9.	711-0677	Ferrule, 5/16-18 x .312
10.	747-1136	Headlamp Retainer
11.	712-3010	Hex Nut, 5/16-18
12.	714-0104	Internal Cotter Pin
13.	725-1672	Lens Assembly / Lamp Housing

14.720-0201A Chute Crank Knob

15.	720-0284	Wing Knob, 5/16-18
16.	726-0100	Push Cap, 3/8
17.	736-0185	Flat Washer, .375 x .738 x .063
18.	736-0242	Bell Washer, .34 x .872

19.731-1341A Plastic Handle Panel (Red)

20.	736-0275	Flat Washer, .344 x .688 x .065
21.	736-0451	Saddle Washer, .32 x .93
22.	710-0276	Carriage Screw, 5/16-18 x 1
23.	747-0620A	Upper Shift Rod
24.	747-0621	Lower Shift Rod
25.	747-0697	Eyebolt
—	735-0234	Eyebolt Grommet (Not Shown)
26.	749-0951	Lower Handle
27.	749-0952	RH Handle (Upper)
28.	749-0953	LH Handle (Upper)
29.	750-0963	Shift Rod Connector
30.	684-0103	Handle Panel Assembly

31.710-0459A Hex Cap Screw, 3/8-24 x 1.5

32.	710-0599	Self Tapping Screw, 1/4-20 x .5
33.	711-0653	Clevis Pin
34.	712-0116	Jam Nut, 3/8-24
35.	714-0507	Cotter Pin, 3/32 x .75

	Ref.	Part No.	Part Description
	No.	Part No.	Part Description
	No.

	36.	732-0145	Compression Spring, .36 x 1.0
	37.	732-0193	Comp. Spring, .39 x .6 x .88
	38.	732-0746	Torsion Spring, .44 x .8
	39.	735-0199A	Rubber Bumper
	40.	736-0105	Bell Washer, .401 x .87 x .063
	41.	736-0119	Lock Washer, 5/16
	42.	736-0509	Special Washer, .35 x .72 x .13
	43.	746-0778	Cable “Z” Fitting
	44.	747-0877	Cam Rod
	45.	748-0362	Cam Handle Lock
	46.	748-0363	Handle Lock Pawl
	47.	784-5619A	Shift Handle
	48.	784-5679	LH Handle Support Bracket
	49.	784-5680	RH Handle Support Bracket
	50.	784-5681	LH Handle Support Bracket
	51.	784-5682	RH Handle Support Bracket
	52.	710-0451	Carriage Bolt, 5/16-18 x .75
	53.	710-0805	Hex Cap Screw, 516-18 x 1.5
	54.	710-0896	Screw, 1/4-14 x .625
	55.	712-0429	Hex Lock Nut, 5/16-18
	56.	712-3027	Hex Flange Lock Nut, 1/4-20

57.731-0851A Lower Chute Flange Keeper

58.

731-1300A

Lower Chute

59.731-1313C Chute Tilt Cable Guide

60.	731-1320	Upper Chute
61.	736-0159	Washer, 5/16
62.	736-0506	Special Washer, .28 x 1.2 x .06
63.	720-0274	Handle Grip
64.	725-1658	Halogen Lamp, 12-volt, 27 Watt
65.	720-0232	Plastic Knob
66.	712-0271	Hex Sems Nut, 1/4-20
67.	629-0059	Halogen Light Harness
68.	684-0036	RH Engagement Handle Ass’y
69.	684-0059	LH Engagement Handle Ass’y
70.	710-1003	Special Screw, #10-16 x .625

25

Image 25

Contents Operator’s Manual Table of Contents Training Important Safe Operation PracticesYour Responsibility Maintenance and StorageAssembling Your Snow Thrower Loose PartsAuger Control Adjustment Final AdjustmentsSkid Shoe Adjustment Tire Pressure AdjustmentShift Lever Know Your Snow ThrowerHeadlight Auger ControlOperating Your Snow Thrower To Engage Drive To Stop EngineTo Engage Augers Tire Chains Optional EquipmentMaking Adjustments Drive Wheels Shift Rod AdjustmentLubrication Maintaining Your Snow ThrowerBelt Removal And Replacement ServiceEngine Auger BeltsShave Plate and Skid Shoes Servicing Friction Wheel RubberAugers Drive BeltOFF-SEASON Storage Problem Cause Remedy TroubleshootingModel Parts ListPart Description Drive Clutch Cable Model Model Model 12 11 1915 Model Model Lens Assembly / Lamp Housing Page Page MANUFACTURER’S Limited Warranty