Poulan 437986, 96192004201, PR624 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 18

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Exploded KEY Part Description Auger Assembly RH Auger HousingAuger Assembly LH Scrapper BARSkid Plate LH Auger BearingBearing Plug Skid Plate RHWasher Knob BlackPOP Rivet Plastic WasherCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadRepair Parts Snow Thrower - Model Number PR624 Handles 419797X431Lower Handle Knob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomInterlock CAM Console PanelInterlock Spring Torsion SpringRepair Parts Snow Thrower - Model Number PR624 Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PIN427963X421 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler Pulley432331X428 Repair Parts Snow Thrower - Model Number PR624 WheelsWheel Assembly LH 432332X428Safety Ignition KEY Snow Thrower - Model Number422663 Repair Parts Snow Thrower - Model Number PR624 Decals 181037DECAL, Danger Service Notes Service Notes Limited Warranty

PR624, 437986, 96192004201 specifications

The Poulan 96192004201,437986,PR624 is a versatile and powerful snow thrower designed for efficient snow removal during harsh winter conditions. This model stands out due to its robust features and cutting-edge technologies, making it a popular choice among homeowners and professionals alike.

One of the key features of the PR624 is its powerful 24-inch clearing width, which allows users to tackle large areas of snow effectively. The machine's heavy-duty auger system is engineered to break through dense, compacted snow, ensuring that even the toughest winter storms can be managed with ease. The adjustable chute is another significant attribute, enabling users to direct the discharged snow exactly where they want, whether onto driveways, sidewalks, or lawns.

Equipped with a reliable, high-performance engine, the PR624 offers impressive start-up capabilities and smooth operation. This snow thrower is designed to handle a variety of snow types, from light flurries to heavy, wet snow, making it a versatile tool for various winter conditions. The engine’s efficiency enhances its performance while reducing fuel consumption, contributing to both cost savings and environmental benefits.

The PR624 features a user-friendly control panel, allowing for simple adjustments and operations even in challenging weather conditions. Its ergonomic handles provide comfort during extended use, reducing fatigue for the operator. Furthermore, the intuitive gear shift options facilitate seamless transitions between different speeds, ensuring optimal maneuverability on driveways or walkways.

Safety is a top priority in the design of the Poulan 96192004201,437986,PR624. It is equipped with several safety features, including an emergency shut-off mechanism, that provides peace of mind during operation. The durable construction materials and thoughtful design also make this snow thrower capable of withstanding harsh winter elements, ensuring longevity and reliability over the years.

Overall, the Poulan 96192004201,437986,PR624 snow thrower is an excellent investment for anyone needing an efficient and reliable way to manage snow accumulation during the winter months. Its combination of power, ease of use, and thoughtful design makes it a standout choice in the realm of snow removal equipment.
Top Page Image Contents