Poulan 96198002701 Parts Packed Separately in Carton, Assembly / PRE-OPERATION, Tool BOX See Fig

Page 4

PARTS PACKED SEPARATELY IN CARTON

	(1) POWER CORD	(1) MULTI-	(3) RETAINER
	(198563)
		WRENCH	SPRINGS

		(180684)	(169675)

	(2) SHEAR BOLTS 1/4-20 x 1-3/4	(2) LOCKNUTS
	(2) SHEAR BOLTS 1/4-20 x 1-3/4		1/4-20
	(192090)		1/4-20
	(192090)		(73800400)
			(73800400)
(2) FLAT WASHERS
	SAFTEY
	IGNITION KEY (S)
	(422663)
(2) CARRIAGE BOLTS	(1) LOCKNUT		(1) CARRIAGE BOLT
3/8-16 x 2.25	5/16-18		5/16-18 x 5/8
	(751153)		(72250505)

		(1) WASHER 3/8	(1) LOCKNUT 3/8	(1) LOCKNUT	(1) SHOULDER
	(2) HANDLE KNOBS			1/4-20	BOLT 1/4-20	(1) SPRING
		(19131316)	(73800600)	(191730)	(179829)	(184505)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 9)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

4

Image 4

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs a and 8B Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing Auger Assembly LHAuger Assembly RH KEY Part Description23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Bearing Bearing PlugKnob Black POP RivetShoulder Screw Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot Bracket196944X007 Panel Bracket LH 196943X007 Panel Bracket RH Handle GripWasher Lower TubeSpacer RetainerKnob RED Handle KnobImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightAxle Shaft SprocketExploded Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateCover Assembly Complete LCT EngineFrame 427963X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Wheel Assembly RHCable Bracket LH Cable Bracket RHCover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 422663DECAL, Danger 181037DECAL, DANGER, Deflector Limited Warranty