Poulan 430352 Parts Packed Separately in Carton, Assembly / PRE-OPERATION, Tool BOX See Fig

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) FUEL STABILIZER PACKET

(1) MULTI-

 

WRENCH

 

(180684)

(1) POWER CORD

SAFTEY IGNITION KEY(S)

 

(198563)

(193071)

 

 

(1) AUGER CONTROL ROD

 

(1) DISCHARGE CHUTE

 

(2) FLAT WASHERS

 

 

EXTRA SHEAR BOLTS AND NUTS

 

(2) SHOULDER

(2) LOCKNUTS

(2) CARRIAGE BOLTS

BOLT 1/4-20 x 1-3/4

1/4-20

3/8-16 x 2.25

(192090)

(73800400)

 

ROTATOR HEAD MOUNTING

(3) RETAINER

SPRINGS(2) HANDLE KNOBS (169675)

(1) WASHER 3/8

(1) LOCKNUT 3/8

(19131316)

(73800600)

CHUTE DEFLECTOR REMOTE CONTROL

(1) LOCKNUT

(1) CARRIAGE BOLT

(1) LOCKNUT

(1) SHOULDER

(1) SPRING

5/16-18

5/16-18 x 5/8

1/4-20

BOLT 1/4-20

(751153)

(72250505)

(191730)

(179829)

(184505)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1. Remove all accessible loose parts and parts boxes

 

from carton.

4

 

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 8)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigsTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting 23 22 KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger Assembly LH Auger Assembly RHSkid Plate LH Skid Plate RHLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadChute Weldment Deflector WeldmentDeflector Seal StrapRepair Parts Snow Thrower - Model NO. XT824ES Handles Lower Tube Pivot SupportInterlock Spring Interlock CAMSpacer Knob REDHandle Knob Washer 3/8Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. XT824ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft Roll PIN 3/16Sprocket Clik PINEngine Model 12A114 Frame423185X505 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower - Model NO. XT824ES Wheels Wheel Assembly LHSafety Ignition KEY Repair Parts Snow Thrower - Model NO. XT824ES BAG of Parts193071 Repair Parts Snow Thrower - Model NO. XT824ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty
Top Page Image Contents