Poulan 430352, 96192003301 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

	AUGER	DISCHARGE CHUTE
ELECTRIC	AUGER	CONTROL LEVER
ELECTRIC	CONTROL	CONTROL LEVER
START BUTTON	CONTROL
START BUTTON	LEVER	DRIVE SPEED
	LEVER	DRIVE SPEED
RECOIL		CONTROL LEVER	TRACTION
RECOIL			TRACTION
(AUXILIARY)			DRIVE
STARTER			CONTROL
HANDLE			LEVER
	CHUTE
DEFLECTOR
			LIGHT

IGNITION

KEYON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

DISCHARGE

CHUTE

CLEAN-OUT TOOL

FIG. 8

CHUTE DEFLECTOR KNOB

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

8

Image 8

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigsTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting 23 22 KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing PlugAuger Assembly LH Auger Assembly RHSkid Plate LH Skid Plate RHLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadChute Weldment Deflector WeldmentDeflector Seal StrapRepair Parts Snow Thrower - Model NO. XT824ES Handles Lower Tube Pivot SupportInterlock Spring Interlock CAMSpacer Knob REDHandle Knob Washer 3/8Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. XT824ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft Roll PIN 3/16Sprocket Clik PINEngine Model 12A114 Frame423185X505 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower - Model NO. XT824ES Wheels Wheel Assembly LH193071 Repair Parts Snow Thrower - Model NO. XT824ES BAG of PartsSafety Ignition KEY Repair Parts Snow Thrower - Model NO. XT824ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty