Poulan 430352, 96192003301 owner manual To Throw Snow See Fig, Using the CLEAN-OUT Tool See Fig

Page 10

OPERATION

TO THROW SNOW (See Fig. 12)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 12

USING THE CLEAN-OUT TOOL (See Fig. 13)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac- cidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

DISCHARGE CHUTE

CLEAN-OUT

TOOL

MOUNTING

CLIP

FIG. 13

•Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine.

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous- ing and the discharge chute.

TO MOVE FORWARD AND BACKWARD (See Fig. 14)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

•Squeeze traction drive control lever to handle to engage the drive system.

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

•Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

•Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 14

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigsTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting 23 22 KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing PlugSkid Plate LH Auger Assembly LHAuger Assembly RH Skid Plate RHCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadDeflector Seal Chute WeldmentDeflector Weldment StrapRepair Parts Snow Thrower - Model NO. XT824ES Handles Interlock Spring Lower TubePivot Support Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. XT824ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PIN423185X505 Engine Model 12A114Frame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyRepair Parts Snow Thrower - Model NO. XT824ES Wheels Wheel Assembly LHSafety Ignition KEY Repair Parts Snow Thrower - Model NO. XT824ES BAG of Parts193071 181037 Repair Parts Snow Thrower - Model NO. XT824ESDecals DECAL, DangerService Notes Service Notes Limited Warranty
Top Page Image Contents